Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to B+ in Front Pretensioner Squib RH Circuit

DTC B0133/62 Short to B+ in Front Pretensioner Squib RH Circuit

DESCRIPTION

The front pretensioner squib RH circuit consists of the center airbag sensor assembly and the front seat outer belt assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0133/62 is recorded when a short to B+ is detected in the front pretensioner squib RH circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)

CHECK FRONT SEAT OUTER BELT ASSEMBLY RH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front seat outer belt assembly RH.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire No. 2.

CAUTION: Never connect a tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory.
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs.

OK: DTC B0133/62 is not output.

HINT: Codes other than DTC B0133/62 may be output at this time, but they are not related to this check.

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

2 CHECK FLOOR WIRE NO.2 (FRONT PRETENSIONER SQUIB RH CIRCUIT)

CHECK FLOOR WIRE NO.2

  1. Disconnect the connector from the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position.
  4. Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Connect the connectors to the front seat outer belt assembly RH and the center airbag sensor assembly.
  4.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Clear the DTCs stored in memory.
  7.  Turn the ignition switch to the LOCK position.
  8.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  9.  Check the DTCs.

OK: DTC B0133/62 is not output.

HINT: Codes other than code B0133/62 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

Short to GND in Front Pretensioner Squib RH Circuit
DTC B0132/61 Short to GND in Front Pretensioner Squib RH Circuit DESCRIPTION The front pretensioner squib RH circuit consists of the center airbag sensor assembly and the front seat outer belt a ...

Short in Front Pretensioner Squib LH Circuit
DTC B0135/73 Short in Front Pretensioner Squib LH Circuit DESCRIPTION The front pretensioner squib LH circuit consists of the center airbag sensor assembly and the front seat outer belt assembly ...

Other materials:

Evaporator temperature sensor circuit
DESCRIPTION The evaporator temperature sensor (A/C thermistor) is installed on the evaporator in the air conditioning unit. It detects the temperature of the cooled air that has passed through the evaporator and its signal is used to control the air conditioning. It sends a signal to the A/C ...

Open in ABS Motor Relay Circuit
DESCRIPTION The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor. If the voltage supplied to the motor relay (+BM) is below the DTCs detection threshold due to low voltage from the battery ...

How to proceed with troubleshooting
HINT: Troubleshoot in accordance with the procedures on the following pages 1 VEHICLE BROUGHT TO WORKSHOP 2 CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK 3 INSPECT COMMUNICATION FUNCTION OF LARGE-SCALE MULTIPLEX COMMUNICATION SYSTEM (BEAN) Use the intelligent tester to check for normal ...

В© 2011-2019 Copyright www.tsienna.net