Toyota Sienna Service Manual: Removal
HINT:
On the RH side, use the same procedures as on the LH side.
1. REMOVE SLIDE DOOR
- Remove the rear door scuff plate (See page IR-7).
- Remove the back door scuff plate (See page ED-
214).
- Remove the quarter trim panel (See page IR-9).
- Remove the upper rail cushion from the rail.
- Disconnect the 2 connectors from the body side and
remove the bolt and wire.
- Open the quarter glass.
- Using a screwdriver, disengage the clip and 2 claws,
remove the rail end moulding.
HINT:
Tape the screwdriver tip before use.
- Remove the 2 bolts and bracket center No. 2
together with the tensioner (color: white).
- Remove the tensioner from the bracket center No.
2.
- Remove the 2 bolts and bracket center No. 1
together with the tensioner (color: black).
- Remove the tensioner from the bracket center No.
1.
- Remove the 2 nuts and open stop.
- Rotate the base of the slide door roller lower in the
direction indicated by arrow in the illustration and
then remove the roller from the cut area of the lower
rail from the body side.
- Move the slide door rearward and then remove the
slide door roller upper from the cut area in the rear
part of the slide door rail upper.
- Move the slide door further rearward and then
remove the slide door hinge center from the rear
part of the slide door rail center. Then, remove the
slide door.
2. REMOVE SLIDE DOOR RAILS
- Remove the roof headlining (See page IR-6).
- Remove the 2 bolts, 2 nuts and the rail upper.
- Remove the 2 screws and rear side rail.
- Remove the 3 screws and rail center
3. REMOVE SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY LH
- Disconnect the 2 cables.
- Remove the 2 bolts and full open stop lock.
4. REMOVE SLIDE DOOR ROLLER ASSEMBLY LOWER LH
- Remove the 3 bolts and roller.
5. REMOVE SLIDE DOOR HINGE ASSEMBLY CENTER LH
- Remove the 3 bolts and hinge.
- LH side:
Remove the cover.
6. REMOVE SLIDE DOOR ROLLER ASSEMBLY UPPER
- Remove the 2 bolts and roller.
1. REMOVE REAR DOOR WINDOW FRAME MOULDING
REAR LH (See page ET-31)
2. REMOVE REAR DOOR WINDOW FRAME MOULDING
SUB-ASSEMBLY LH (See page ET-32)
3. REMOVE SLIDE DOOR WINDOW GARNISH LH
Fully o ...
Other materials:
VSC Warning Light does not Come ON
DESCRIPTION
The skid control ECU is connected to the combination meter via CAN and
multiplex communications.
If the skid control ECU stores DTCs to shut down TRAC and VSC operation, the VSC
warning light comes
on in the combination meter.
WIRING DIAGRAM
Refer to VSC Warning Light Remains ...
Sensor signal check by test mode (signal check) (when using sst check wire)
(a) When having replaced the skid control ECU and/or
yaw rate and deceleration sensor, perform zero
point calibration of the yaw rate and deceleration
sensor.
HINT:
If the ignition switch is turned from the ON
position to the ACC or off during test mode
(signal check), DTCs of the signal ...
Removal
1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
HINT:
See page EM-26
2. REMOVE OIL LEVEL GAUGE GUIDE SUBASSEMBLY
(See page EM-39)
3. REMOVE NO. 1 OIL PIPE (See page EM-77)
4. REMOVE OIL PIPE (See page EM-77)
5. REMOVE CRANKSHAFT PULLEY (See page EM-79)
6. SEPARATE OIL COOLER PIPE
(a) Remove th ...