Toyota RAV4 manuals

Toyota Sienna Service Manual: Back door lock

Toyota Sienna Service Manual / Door lock / Back door lock

INSPECTION

1. INSPECT BACK DOOR LOCK ASSEMBLY (W/O CLOSER)

INSPECT BACK DOOR LOCK ASSEMBLY

  1.  Check operation of the door lock.
  1.  Using a screwdriver, push the latch in order to put the back door lock in the locked condition (full-latch position).
  2.  Connect the battery positive (+) lead to terminal 3 and the battery negative (-) lead to terminal 1.

    Then, check operation of the latch.

    Standard: The latch turns to the open-latch position If operation is not as specified, replace the door lock assembly.

  3.  Inspect motor operation when battery voltage is applied to the terminals.

Standard

Standard

If operation is not as specified, replace the door lock assembly.

  1.  Check the back door courtesy switch resistance.
  1.  Check the resistance between the terminals of the courtesy switch.

Standard resistance

Standard resistance

If the result is not as specified, replace the door lock assembly.

2. INSPECT BACK DOOR LOCK ASSEMBLY (W/ CLOSER)

INSPECT BACK DOOR LOCK ASSEMBLY

  1.  Check operation of the door lock.
  1.  Using a screwdriver, push the latch in order to put the back door lock in the locked condition (full-latch position).
  2. Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2.

    Then, check operation of the latch.

    Standard: The latch turns to the open-latch position

  3.  Inspect motor operation when battery voltage is applied to the terminals.

Standard

Standard

HINT: If operation is not as specified, replace the door lock assembly.

INSPECT BACK DOOR LOCK ASSEMBLY

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance (Courtesy switch)

Standard resistance (Courtesy switch)

HINT: If the result is not as specified, replace the door lock assembly.

  1.  Measure the resistance according to the value(s) in the table below.

Standard resistance (Back door latch switch)

Standard resistance (Back door latch switch)

HINT: If the result is not as specified, replace the door lock assembly.

  1.  Measure the resistance according to the value(s) in the table below.

Standard resistance (Position switch)

Standard resistance (Position switch)

HINT: If the result is not as specified, replace the door lock assembly.

  1.  Measure the resistance according to the value(s) in the table below.
  1.  Full-latch: Connect the battery positive (+) lead to connector terminal 7 and the negative (-) lead to connector terminal 5.

Standard resistance

Standard resistance

HINT: If the result is not as specified, replace the door lock assembly.

Rear door lock
INSPECTION 1. INSPECT REAR DOOR LOCK ACTUATOR ASSEMBLY LH  Apply battery voltage to the door lock and check operation of the motor. OK HINT: If the result is not as specified, r ...

Meter
...

Other materials:

Power Back Door does not Operate
DESCRIPTION The power back door operates only when the power back door main switch is ON. The power back door ECU controls the power back door by activating the back door motor (built into the power back door drive unit) to open / close the back door. A request signal from the satell ...

Engine coolant
The coolant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir when the engine is cold. Reservoir cap “FULL” line “LOW” line If the level is on or below the “LOW” line, add coolant up to the “FULL” line. Coolant selection On ...

Dtc check / clear
Notice:All the stored dtcs and freeze frame data are erased if: 1) the ecm is changed from normal mode to check mode or vice versa; or 2) the ignition switch is turned from on to acc or off while in check mode. Before changing modes, always check and make a note of any dt ...

© 2011-2024 Copyright www.tsienna.net