Toyota RAV4 manuals

Toyota Sienna Service Manual: Center Airbag Sensor Assembly Malfunction

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Center Airbag Sensor Assembly Malfunction

DTC B1100/31 Center Airbag Sensor Assembly Malfunction

DESCRIPTION

The center airbag sensor assembly consists of the center airbag sensor assembly, safing sensor, drive circuit, diagnosis circuit and ignition control, etc.

It receives signals from the airbag sensor, judges whether or not the SRS must be activated, and detects diagnosis system malfunction.

DTC B1100/31 is recorded when a malfunction is detected in the center airbag sensor assembly circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1100/31
  • Short in front airbag sensor RH circuit (to ground)
  • Short in front airbag sensor RH circuit (to B+)
  • Short in front airbag sensor RH circuit
  • Short in front airbag sensor LH circuit (to ground)
  • Short in front airbag sensor LH circuit (to B+)
  • Short in front airbag sensor LH circuit
  • Center airbag sensor assembly malfunction
  • Center airbag sensor assembly
  • Engine room main wire
  • Instrument panel wire

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT: When a trouble code is displayed simultaneously with B1100/31, repair the malfunction indicated by this code (except B1100/31) first.

1 CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front airbag sensor RH and the center airbag sensor assembly.
  4.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 8

2 CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position.
  3.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

Go to step 9

3 CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 10

4 CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

  1. Disconnect the connector from the front airbag sensor LH.
  2. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 11

5 CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position.
  3.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

Go to step 12

6 CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 13

7 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the center airbag sensor assembly, front airbag sensors RH and LH.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B1100/31 is not output.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

8 CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)

CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)

  1. Disconnect the engine room main wire connector from the instrument panel wire.
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

9 CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)

CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the engine room main wire connector from the instrument panel wire.
  4.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5.  Turn the ignition switch to the ON position.
  6.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

10 CHECK ENGINE ROOM MAIN WIRE (SHORT)

CHECK ENGINE ROOM MAIN WIRE (SHORT)

  1. Disconnect the engine room main wire connector from the instrument panel wire.
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

11 CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)

CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)

  1. Disconnect the engine room main wire connector from the instrument panel wire.
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

12 CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)

CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the engine room main wire connector from the instrument panel wire.
  4.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5.  Turn the ignition switch to the ON position.
  6.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

13 CHECK ENGINE ROOM MAIN WIRE (SHORT)

CHECK ENGINE ROOM MAIN WIRE (SHORT)

  1. Disconnect the engine room main wire connector from the instrument panel wire.
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

Short to B+ in Front Pretensioner Squib LH Circuit
DTC B0138/72 Short to B+ in Front Pretensioner Squib LH Circuit DESCRIPTION The front pretensioner squib LH circuit consists of the center airbag sensor assembly and the front seat outer belt ass ...

Half Connection in Center Airbag Sensor Assembly Connectors
DTC B1135/24 Half Connection in Center Airbag Sensor Assembly Connectors DESCRIPTION The center airbag sensor assembly connector has a mechanism that electrically detects half connection. The ...

Other materials:

Current Position Display does not Appear
INSPECTION PROCEDURE 1 CHECK RADIO AND NAVIGATION ASSEMBLY Check if a map disc is inserted into the map disc slot. OK: A map disc is inserted 2 CHECK MAP DISC Check that the map disc is not deformed or cracked. OK: No deformations or cracks appear on the map disc. PROCEED ...

Transmission Fluid Temperature Sensor "A"
DESCRIPTION The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input into the ECM. The ECM applies a voltage to the temperature sensor through ECM terminal THO1. The sensor resistance changes with the transmission f ...

On-vehicle inspection
1. INSPECT FRONT PASSENGER AIRBAG ASSEMBLY (VEHICLE NOT INVOLVED IN COLLISION)  Perform a diagnostic system check.  With the front passenger airbag assembly installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the instrumen ...

В© 2011-2024 Copyright www.tsienna.net