Toyota Sienna Service Manual: Check that initialization has been completed
(a) Confirm that the data of tire pressure of all tires are displayed on the intelligent tester screen.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| TIREPRESS1 | ID1 tire inflation pressure (Absolute pressure) / min.: 100 kPa (1 kgf/cm2, 14 psi) max.: 449.35 kPa (4.5 kgf/cm2, 63 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for absolute pressure is displayed, the data has not been received.* |
| TIREPRESS2 | ID2 tire inflation pressure (Absolute pressure) / min.: 100 kPa (1 kgf/cm2, 14 psi) max.: 449.35 kPa (4.5 kgf/cm2, 63 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for absolute pressure is displayed, the data has not been received.* |
| TIREPRESS3 | ID3 tire inflation pressure (Absolute pressure) / min.: 100 kPa (1 kgf/cm2, 14 psi) max.: 449.35 kPa (4.5 kgf/cm2, 63 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for absolute pressure is displayed, the data has not been received.* |
| TIREPRESS4 | ID4 tire inflation pressure (Absolute pressure) / min.: 100 kPa (1 kgf/cm2, 14 psi) max.: 449.35 kPa (4.5 kgf/cm2, 63 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for absolute pressure is displayed, the data has not been received.* |
HINT:
*: It may take about 5 to 6 minutes until the values are displayed. If the values are not displayed after several minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (See page TW-42).
NOTICE: The following operations can be used instead of above procedure:
1. Turn the ignition switch from OFF to ON.
2. Monitor the tire pressure values of all the wheels using the intelligent tester.
3. If the tire pressure values cannot be displayed on the intelligent tester screen, the initialization has failed.
4. It takes about 5 to 6 minutes to display the tire pressure data.
Initialization procedure
(a) Make sure that the ignition switch is off.
(b) Connect the intelligent tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Select "TIREPRESS" by followi ...
Other materials:
Removal
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1. PRECAUTION
CAUTION: Be sure to read "PRECAUTION" thoroughly before
servicing.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
CAUTION:
Wait for 90 s ...
Display does not Dim when Light Control Switch is Turned ON
INSPECTION PROCEDURE
1 CHECK IMAGE QUALITY SETTING
Enter the display adjustment screen by pressing the
"DISPLAY" switch.
Turn the light control switch to the TAIL position.
Check if "DAY MODE" on the display adjustment is ON.
OK:
"DAY MODE" ...
CD Sound Skips
INSPECTION PROCEDURE
1 CHECK CD
Check the CD.
OK:
The CD is clean.
HINT:
If dirt is on the CD surface, wipe it clean with a soft cloth
from the inside to the outside in a radial direction.
NOTICE:
Do not use a conventional record cleaner or antistatic
preservative.
2 CHECK CD
...
