Toyota RAV4 manuals

Toyota Sienna Service Manual: Diagnosis system

1. CHECK BATTERY VOLTAGE

Standard voltage: 11 to 14 V

If the voltage is below 11 V, recharge the battery before proceeding.

2. CHECK DLC3

CHECK DLC3

(a) The ECU uses the ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.

CHECK DLC3

NOTICE: *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

(b) If the result is not as specified, DLC3 may have a malfunction. Repair or replace the harness and connector.

HINT: Connect the cable of the intelligent tester to DLC3, turn the ignition switch to the ON position and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

3. DIAGNOSIS SYSTEM

(a) DTCs (Normal mode) (1) DTCs are memorized in the tire pressure warning ECU and read by the blinks of the tire pressure warning light or by using the intelligent tester (See page TW-34).

(b) Test mode

(1) By switching from normal mode into test mode (input signal check), you can inspect the tire pressure warning antenna and receiver, each tire pressure warning valve and transmitter, and vehicle speed sensor (See page TW-25).

(c) When there is a problem with the tire pressure warning system, the tire pressure warning light blinks at 0.5-second intervals, and turns on after 1 minute.

4. CHECK TIRE PRESSURE WARNING LIGHT

CHECK TIRE PRESSURE WARNING LIGHT

(a) Turn the ignition switch to the ON position.

(b) Check that the tire pressure warning light comes on for 3 seconds.

If the warning check result is not normal, proceed to the troubleshooting for the tire pressure warning light circuit.

5. TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

HINT: The table below indicates the state of the tire pressure warning light and indicator after the ignition switch ON.

 TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

*1: Comes on and goes off repeatedly at 0.5-second intervals, and comes on after 1 minute.

TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

*2: Comes on and goes off repeatedly at 0.125-second intervals.

TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

*3: Blinks 3 times (1 second on, 1 second off).

TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

*4: Comes on and goes off repeatedly at 0.25-second intervals.

Terminals of ecu
Check tire pressure warning ecu HINT: Inspect the connectors from the back side while the connectors are connected. (a) Disconnect the tire pressure warning antenna and receiver connector. ...

Dtc check / clear
1. DTC CHECK (USING SST CHECK WIRE) (a) Check DTCs. (1) Turn the ignition switch off. (2) Using SST, connect terminals TC and CG of DLC3. SST 09843-18040 (3) Turn the ignition switch to ...

Other materials:

Turbine Speed Sensor Circuit No Signal
DESCRIPTION This sensor detects the rotation speed of the input turbine. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure accor ...

Reassembly
1. INSTALL REAR DOOR WIRE SUB-ASSEMBLY LH Install the wire. NOTICE: When installing the wire, push the areas where the clips are installed in order to prevent damage and deformation. Install the 2 screws. 2. INSTALL REAR DOOR LOCK ASSEMBLY LH Apply MP grease to the slidi ...

Installation
1. INSTALL SEAT POSITION AIRBAG SENSOR  Check that the ignition switch is off. Check that the negative battery (-) terminal is disconnected. CAUTION: After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.  Usin ...

В© 2011-2024 Copyright www.tsienna.net