Toyota Sienna Service Manual: Diagnostic trouble code chart
COMMUNICATION DIAGNOSIS:
DVD PLAYER:
CD PLAYER
IN-DASH CD CHANGER
- ROM Error/ RAM Error
- Absence of Registration Unit/ No Response for Connection Check/ Last Mode Error/ No Response Against ON / OFF Command/ Mode Status Error/ Slave Reset
- No Master/ Connection Check Error
- Transmission Error
- Master Reset/ Voice Processing Device ON Error
- Master Error
- Registration Complete Indication Error/ Registration Demand Transmission/ Multiple Frame Incomplete
- ON / OFF Indication Parameter Error
- DVD Player Mechanical Error/ DVD Insertion and Ejection Error/ DVD Reading Abnormal
- Wrong Disc/ Disc cannot be Read
- DVD-ROM Abnormal
- DVD Error/ Excess Current/ Tray Insertion / Ejection Error
- Eject Error/ Elevator Error/ Clamp Error
- Scratched / Reversed Disc
- High Temperature
- DSP Error
- Disc cannot be Played/ No Playable Files/ Copyright Protection Error
- CD Player Mechanical Error/ CD Insertion and Ejection Error/ CD Reading Abnormal/ CD Changer Mechanical Error/ CD Insertion and Ejection Error/ CD Reading Abnormal
- Wrong Disc/ Disc cannot be Read/ Wrong Disc/ Disc cannot be Read
- CD-ROM Abnormal/ CD-ROM Abnormal
- CD Abnormal/ Excess Current/ Tray Insertion / Ejection Error/ CD Abnormal/ Excess Current/ Tray Insertion / Ejection Error
- Eject Error/ Elevator Error/ Clamp Error/ Eject Error/ Elevator Error/ Clamp Error
- Scratched / Reversed Disc
- High Temperature
- DSP Error/ DSP Error
- Disc cannot be Played/ No Playable Files/ Copyright Protection Error/ Disc cannot be Played/ No Playable Files/ Copyright Protection Error
- Noise Occurs
- Pressing Power Switch does not Turn on System
- No Sound can be Heard from Speakers
- Sound Quality is Bad Only when CD is Played (Volume is Too Low)
- CD cannot be Ejected
- CD cannot be Inserted / Played or CD is Ejected Right After Insertion
- CD Sound Skips
- Radio Broadcast cannot be Received or Poor Reception
- Poor Sound Quality in All Modes (Low Volume)
- Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter
- Steering Pad Switch Circuit
- Illumination Circuit
- Speaker Circuit
- Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier
- Sound Signal Circuit between Radio Receiver and Television Display Assembly
- Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter
- Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier
- Mute Signal Circuit between Radio Receiver and Television Display Assembly
- AVC-LAN Circuit
- Vehicle Speed Signal Circuit between Multi-display and Combination Meter
- Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter
- Radio Receiver Communication Error
- Stereo Component Amplifier Communication Error
- Television Display Assembly Communication Error
- Radio Receiver Power Source Circuit
- Stereo Component Amplifier Power Source Circuit
DTC check / clear
HINT: If the system cannot enter the diagnostic mode,
inspect all AVC-LAN communication signals and repair or replace problem parts.
1. STARTING DIAGNOSTIC MODE
Turn the ignition swit ...
ROM Error/ RAM Error
DTC 01-21 ROM Error
DTC 01-22 RAM Error
DESCRIPTION
INSPECTION PROCEDURE
HINT:
After the inspection is completed, clear the DTCs.
1 REPLACE RADIO RECEIVER
END ...
Other materials:
Memory Switch Circuit
DESCRIPTION
When the seat memory switch M1 or M2 is pressed, the position control ECU &
switch (Seat ECU)
transmits a signal of the memorized mirror position to the outer mirror control
ECU. Then, the outer mirror
control ECU drives the mirror motor.
HINT:
The power mirror control syste ...
Diagnostic trouble code chart
HINT:
The parameters listed in the chart may not confirm exactly to
those read during the DTC check due to the type of
instrument or other factors.
If a trouble code is displayed during the DTC check in the
check mode, check the circuit for the code listed in the table
below. For details of ...
Installation
1. INSTALL STABILIZER BAR FRONT
2. INSTALL FRONT STABILIZER BAR BUSH NO.1
(a) Install the front stabilizer bar bush No. 1.
HINT:
Install the bushing to the outer side of the bushing
stopper on the stabilizer bar as shown in the
illustration.
4. INSTALL RACK & PINION POWER STEERING GEA ...
