Toyota Sienna Service Manual: Disassembly
1. REMOVE SIDE DEFROSTER NOZZLE DUCT NO.1
(a) Remove the 2 screws <C> and defroster nozzle duct No. 1.
2. REMOVE SIDE DEFROSTER NOZZLE DUCT NO.2
(a) Remove the 2 screws <C> and defroster nozzle duct No. 2.
3. REMOVE DEFROSTER NOZZLE ASSEMBLY
(a) Remove the 4 screws <C> and defroster nozzle assembly.
4. REMOVE HEATER TO REGISTER DUCT NO.1
(a) Remove the 3 screws <C> and heater to register duct No. 1.
5. REMOVE HEATER TO REGISTER DUCT NO.2
(a) Remove the 3 screws <C> and heater to register duct No. 2.
6. REMOVE HEATER TO REGISTER DUCT NO.3
(a) Remove the 2 screws <C> and heater to register duct No. 3.
7. REMOVE SIDE DEFROSTER NOZZLE LH
8. REMOVE SIDE DEFROSTER NOZZLE RH
9. REMOVE INSTRUMENT PANEL FINISH PANEL RETAINER LOWER NO.3
(a) Remove the 2 screws <C> and instrument panel finish panel retainer lower No. 3.
10. REMOVE INSTRUMENT CLUSTER FINISH PANEL REINFORCEMENT
(a) Remove the screw <C> and instrument cluster finish panel reinforcement.
11. REMOVE DEFROSTER DUCT BRACKET NO.1
(a) Remove the screw <C> and defroster duct bracket No. 1.
12. REMOVE INSTRUMENT FINISH PANEL RETAINER LOWER
(a) Remove the screw <C> and instrument finish panel retainer lower.
13. REMOVE INSTRUMENT FINISH PANEL RETAINER LOWER NO.2
(a) Remove the screw <C> and instrument finish panel retainer lower No. 2.
14. REMOVE INSTRUMENT PANEL FINISH PANEL RETAINER NO.1
(a) Remove the 2 screws <C> and instrument panel finish panel retainer No. 1.
15. REMOVE INSTRUMENT PANEL BOX DOOR SUBASSEMBLY NO.2
16. REMOVE ANTENNA CORD SUB-ASSEMBLY
17. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)
18. REMOVE INSTRUMENT PANEL WIRE NO.2
- Remove the 2 screws <C>.
- Disengage the 7 clamps and remove the instrument panel wire No. 2.
19. REMOVE INSTR PNL PASS L/DOOR AIR BAG ASSEMBLY
Removal
1. BOLT, SCREW AND NUT TABLE
The bolts, the screws and the nuts, which are
necessary for installation and removal of the
instrument panel are shown in the illustration below
with alpha ...
Reassembly
1. INSTALL INSTR PNL PASS L/DOOR AIR BAG
ASSEMBLY
2. INSTALL INSTRUMENT PANEL WIRE NO.2
3. INSTALL NAVIGATION ANTENNA ASSEMBLY
4. INSTALL ANTENNA CORD SUB-ASSEMBLY
5. INSTALL INSTRUMENT PANEL BOX ...
Other materials:
Internal Control Module Random Access Memory
(RAM) Error
DTC P0604 Internal Control Module Random Access Memory
(RAM) Error
DESCRIPTION
The ECM continuously monitors its own internal memory status, internal
circuits, and output signals
transmitted to the throttle actuator. This self-check ensures that the ECM is
functioning properly. If any
malfu ...
Shift lock system
On-vehicle inspection
1. CHECK SHIFT LOCK OPERATION
(a) Move the shift lever to the P position.
(b) Turn the ignition switch to the LOCK position.
(c) Check that the shift lever cannot be moved to any
position other than P.
(d) Turn the ignition switch to the on position, depress
the br ...
Removal
1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
CAUTION: Wait for 90 seconds after disconnecting the cable
to prevent the airbag working.
2. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Disengage the 4 clips and remove the instrument
cluster finish panel sub-assembly.
...
