Toyota RAV4 manuals

Toyota Sienna Service Manual: Disposal

HINT:

CAUTION:

1. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

HINT: Prepare a battery as the power source to deploy the airbag.

  1.  Check the function of the SST.
  2.  Precaution.
  3.  Disconnect the cable from the negative battery terminal.

    CAUTION: Wait for 90 seconds after disconnecting the cable to prevent the airbag working.

  4.  Remove the 4 bolts from the front seat assembly.

HINT: Keep the front seat assembly in the cabin.

  1. Install the SST.
  1.  Disconnect the connector (yellow colored one) from the front seat side airbag assembly.

NOTICE: When handling the airbag connector, take care not to damage the airbag wire harness.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1. Connect the SST connector to the front seat side airbag assembly connector.

    SST 09082-00700, 09082-00750 NOTICE: To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

  2.  Install the 4 bolts to the front seat assembly.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1.  Move the SST at least 10 m (33 ft) away from the vehicle front side window.
  2.  Maintaining enough clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

    NOTICE: Take care not to damage the SST wire harness.

  3.  Connect the red clip of the SST to the battery positive (+) terminal and the black clip of the SST to the negative (-) terminal.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1.  Deploy the airbag.
  1.  Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.
  2.  Press the SST activation switch and deploy the airbag.

CAUTION:

HINT: The airbag is deployed as the LED of the SST activation switch comes on.

2. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

NOTICE:

HINT: Prepare a battery as the power source to deploy the airbag.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1.  Check the function of the SST.
  2.  Remove the front seat side airbag assembly.
  1.  Remove the front seat assembly.
  1.  Remove the 2 nuts and the front seat side airbag assembly from the seatback assembly.

CAUTION:

  1.  Using a service-purpose wire harness for the vehicle, tie down the front seat side airbag assembly to the tire.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

Wire harness:
Stripped wire harness section: 1.25 mm2 or more (0.0019 in.2 or more)

HINT: To calculate the area of the stripped wire harness section: Area = 3.14 x (Diameter)2 divided by 4

CAUTION: If the wire harness is too thin or an alternative object is used to tie down the front seat side airbag assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1. Install the 2 nuts to the front seat side airbag assembly.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1. Wind the wire harness around each of the stud bolts of the front seat side airbag assembly as shown in the illustration.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1. Position the front seat side airbag assembly inside the tire as shown in the illustration.

Tire size: Must exceed the following dimensions
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)

CAUTION:

NOTICE: The tire will be damaged by airbag deployment, so use an extra tire.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1. Install the SST.
  1.  Connect the SST connector to the front seat side airbag assembly connector.

    SST 09082-00750

  1. Place the tires.
  1.  Place at least 2 tires under the tire which the front seat side airbag assembly is tied to.
  2.  Place at least 2 tires over the tire which the front seat side airbag assembly is tied to. The top tire should have a disc wheel installed.

NOTICE: Do not place the SST connector under the tire because it could be damaged.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1. Tie the tires together with 2 wire harnesses.

CAUTION: Make sure that the wire harness is tight.

Looseness in the wire harness results in the tires coming free due to the shock when the airbag is deployed.

  1. Install the SST.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1.  Connect the SST connector.

    SST 09082-00700 NOTICE: To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

  2.  Move the SST at least 10 m (33 ft) away from the airbag tied down to the tires.
  1.  Deploy the airbag.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

  1.  Connect the red clip of the SST to the battery positive (+) terminal and the black clip of the SST to the negative (-) terminal.
  2.  Check that no one is within a 10 m (33 ft) radius of the tire which the front seat side airbag assembly is tied to.
  3.  Press the SST activation switch and deploy the airbag.

CAUTION: When deploying the airbag, make sure that no one is near the tire.

HINT: The airbag is deployed as the LED of the SST activation switch comes on.

  1. Dispose of the front seat side airbag assembly.

DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:

  1.  Remove the front seat side airbag assembly from the tire.
  2.  Place the front seat side airbag assembly in a plastic bag, tie it tightly and dispose of it as other general part disposal.
On-vehicle inspection
1. FRONT SEAT SIDE AIRBAG ASSEMBLY (VEHICLE NOT INVOLVED IN COLLISION)  Perform a diagnostic system check.  With the front seat side airbag assembly installed on the vehicle, pe ...

Center airbag sensor assembly
COMPONENTS ...

Other materials:

High Temperature
DTC 44-47 High Temperature DESCRIPTION DTC No. DTC Detecting Condition Trouble Area 44-47 Sensor detects that DVD unit temperature is high. (Over 80C) Television display assembly INSPECTION PROCEDURE HINT: After the inspection is completed, ...

Reassembly
1. INSTALL REAR SEAT STAY SUB-ASSEMBLY  Install the rear seat stay sub-assembly with the nut. Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 2. INSTALL NO. 2 SEAT CUSHION SPRING ASSEMBLY LH 3. INSTALL LOCUS CABLE LH  Install the locus cable LH with the nut. Torque: 5.5 N*m (56 kg ...

Open in Curtain Shield Squib LH Circuit
DTC B1166/88 Open in Curtain Shield Squib LH Circuit DESCRIPTION The curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH. The circuit instructs the SRS to deploy when deployment conditions are met. DTC B1166/88 is recorde ...

В© 2011-2024 Copyright www.tsienna.net