Toyota RAV4 manuals

Toyota Sienna Service Manual: Dtc check / clear

1. DTC CHECK/CLEAR (WHEN USING INTELLIGENT TESTER):

DTC CHECK/CLEAR (WHEN USING INTELLIGENT TESTER)

(a) DTC check

(1) Connect the intelligent tester to the DLC3.

(2) Turn the ignition switch to the ON position.

(3) Read the DTCs following the prompts on the tester screen.

(b) DTC clear

(1) Connect the intelligent tester to the DLC3.

(2) Turn the ignition switch to the ON position.

(3) Operate the intelligent tester to clear the codes.

HINT: Refer to the intelligent tester operator's manual for further details.

2. DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE):

DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE)

(a) DTC check

(1) Using SST, connect terminals TC and CG of the DLC3.

SST 09843-18040

(2) Turn the ignition switch to the ON position.

(3) Read DTC from the ABS and VSC warning lights on the combination meter.

HINT: If no code appears, inspect the TC and CG terminal circuit, and ABS and VSC warning light circuits.

(4) As an example, the illustration below shows the blinking patterns of the normal system code and trouble codes 11 and 21.

DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE)

(5) Codes are explained in the code table (See page BC-88).

(6) After completing the check, disconnect terminals TC and CG of the DLC3, and turn off the display.

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.

DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE)

(b) DTC clear

(1) Using SST, connect terminals TC and CG of the DLC3.

SST 09843-18040 (2) Turn the ignition switch to the ON position.

DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE)

(3) Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

(4) Check that the warning light indicates the normal system code.

(5) Remove the SST from the terminals of the DLC3.

HINT: Clearing the DTCs cannot be performed by removing the battery cable or the ECU-IG fuse.

3. END OF DTC CHECK/CLEAR:

(a) Turn the ignition switch to the ON position.

(b) Check that the ABS and VSC warning lights go off within approximately 3 seconds.

Terminals of ecu
1. Terminal of ECU (*1): Models with dynamic laser cruise control (*2): 2WD model 2. Terminal Inspection (a) Disconnect the connector and measure the voltage or resistance on the wire harness ...

Freeze frame data
1. FREEZE FRAME DATA (a) The vehicle (sensor) status, stored during ABS and/ or VSC operation or at the time of an error code detection, can be displayed by the intelligent tester. (b) Only one ...

Other materials:

Crankshaft Position - Camshaft Position Correlation
DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) DTC P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) DTC P0019 Crankshaft Position - Camshaft Position Corr ...

Radio Broadcast cannot be Received or Poor Reception
INSPECTION PROCEDURE 1 CHECK RADIO RECEIVER Check the radio's automatic station search function.  Check the radio's automatic station search function by activating it. OK: The radio's automatic station search function works properly. 2 CONFIRM MODEL Result 3 INSPECT RADIO ...

System description
1. BRIEF DESCRIPTION The CAN (Controller Area Network) is a serial data communication system for real time application. It is a vehicle multiplex communication system which has a high communication speed (500 kbps) and the ability to detect malfunctions. By pairing the CANH and CANL bu ...

В© 2011-2024 Copyright www.tsienna.net