Toyota Sienna Service Manual: DTC check / clear
HINT:
1. START DIAGNOSTIC MODE
- There are 2 methods to start diagnostic mode. Start
the mode by using one of them.
- Method 1
- Start the engine.
- While pressing and holding the "INFO" switch,
operate the light control switch: OFF
Turn ON
Turn OFF
Turn ON
Turn OFF
Turn
ON Turn OFF.
- The diagnostic mode starts and the "System
Check Mode" screen will be displayed. Service
inspection starts automatically and the result will
be displayed.
- Method 2
- Start the engine.
- Switch to the "Display Check" screen.
- From the display quality adjustment screen,
touch the corners of the screen in the following
order: upper left lower left
upper left
lower left upper left
lower left.
- The diagnostic mode starts and the "System
Check Mode" screen will be displayed. Service
inspection starts automatically and the result will
be displayed.
2. FINISH DIAGNOSTIC MODE
- There are 2 methods to end diagnostic mode. Use
one of them.
- Turn the ignition switch off.
(2) Press and hold the "DISP
- switch for 3
seconds.
3. DIAGNOSIS MENU
- The "Diagnosis MENU" screen will be displayed by
pressing the menu switch on the "System Check
Mode" screen
4. CHECK DTC
- Read the system check result.
- If the check result is "EXCH", "CHEK" or "Old",
touch the displayed check result to view the
results on the "Unit Check Mode" screen and
record them.
HINT:
- If all check results are "OK", go to
communication DTC check.
- If a device name is not known, its physical
address is displayed.
HINT:
When proceeding to view the results of another
device, press the service switch to return to the
"System Check Mode" screen. Repeat this step.
- Read the communication diagnostic check result.
- Return to the "System Check Mode" screen, and
press the "LAN Mon" switch to enter the "LAN
Monitor" screen.
- If the check result is "CHEK" or "Old", touch the
displayed check result to view the results on the
individual communication diagnostic screen and
record them.
HINT:
- If all check results are "No Err", the system
judges that no DTC exists.
- The sub-code (relevant device) will be
indicated by its physical address.
- When proceeding to view the results of
another device, press the "Service" switch to
return to the original "LAN Monitor" screen.
Repeat this step.
5. DTC CLEAR/RECHECK
- Clear DTC
- Press the "Code CLR" switch for 3 seconds.
- The check results are cleared
- Recheck
- Press the "Recheck" switch.
- Confirm that all diagnostic codes are "OK" when
the check results are displayed. If a code other
than "OK" is displayed, troubleshoot again.
- Press the "LAN Mon" switch to change to the
"LAN Monitor" screen.
- Confirm that all diagnostic codes are "No Err". If
a code other than "No Err" is displayed,
troubleshoot again.
1. RADIO AND NAVIGATION ASSEMBLY
*1: with Rear Seat Entertainment System
Reference: waveform 1
HINT:
Terminal: VV+ - VV-
Gauge set: 200 mV/DIV, 10 μ ...
COMMUNICATION DIAGNOSIS:
SW:
SW WITH NAME:
SW CONVERTING:
COMMAND SW:
FRONT MONITOR:
DVD PLAYER:
TELEPHONE:
NAVI:
IN-DASH CD CHANGER:
GPS:
CAMERA U ...
Other materials:
Short to B+ in Rear Curtain Shield Squib RH
Circuit
DTC B1633/82 Short to B+ in Rear Curtain Shield Squib RH
Circuit
DESCRIPTION
The rear curtain shield squib RH circuit consists of the center airbag sensor
assembly and the curtain
shield airbag assembly RH.
The circuit instructs the SRS to deploy when deployment conditions are met.
DTC B ...
Removal
1. REMOVE CENTER REAR SEAT LAP TYPE BELT
ASSEMBLY (for 8-Passenger)
HINT:
Refer to the instructions for disassembly of the rear No. 1 seat assembly (for
center seat).
Remove the bolt and center seat lap type belt
assembly.
2. REMOVE CENTER REAR NO. 2 SEAT LAP BELT
ASSEMBLY WITH ...
ECM Power Source Circuit
DESCRIPTION
When the ignition switch is turned to the ON position, the battery voltage is
applied to terminal IGSW of
the ECM. The ECM MREL output signal causes a current to flow to the coil,
closing the contacts of the EFI
relay and supplying power to terminal +B of the ECM.
If the igniti ...