Toyota Sienna Service Manual: ECM Power Source Circuit
DESCRIPTION
When the ignition switch is turned to the ON position, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.
If the ignition switch is turned off, the ECM holds the EFI relay ON for a maximum of 2 seconds to allow for the initial setting of the throttle valve.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 INSPECT ECM (+B VOLTAGE)
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage 
2 CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
(a) Disconnect the E11 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance: 
(c) Reconnect the ECM connector.
3 INSPECT ECM (IGSW VOLTAGE)
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table below
Standard voltage 
4 CHECK FUSE (IGN FUSE)
(a) Remove the IGN fuse from the driver side junction block.
(b) Measure the IGN fuse resistance.
Standard resistance: Below 1 Ω
(c) Reinstall the IGN fuse.
5 CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
(a) Disconnect the E4 ECM connector.
(b) Disconnect the I15 ignition switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance: 
(d) Reconnect the ECM connector.
(e) Reconnect the ignition switch connector.
6 INSPECT IGNITION SWITCH ASSEMBLY
(a) Inspect the ignition or starter switch assembly (See page ST-16).
7 CHECK FUSE (AM2 FUSE)
(a) Remove the AM2 fuse from the engine room junction block.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance: Below 1 Ω
(c) Reinstall the AM2 fuse
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)
8 INSPECT ECM (MREL VOLTAGE)
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage 
9 CHECK FUSE (EFI NO.1 FUSE)
(a) Remove the EFI No. 1 fuse from the engine room junction block.
(b) Measure the EFI No. 1 fuse resistance.
Standard resistance: Below 1 Ω
(c) Reinstall the EFI No. 1 fuse.
10 INSPECT RELAY (EFI RELAY)
(a) Remove the EFI relay from the engine room junction block.
(b) Measure the EFI relay resistance.
Standard resistance 
(c) Reinstall the EFI relay.
11 CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM)
(a) Check the harness and connector between the EFI relay and ECM.
(1) Remove the EFI relay from the engine room junction block.
(2) Disconnect the E4 ECM connector.
(3) Measure the resistance according to the value(s) in the table below.
Standard resistance: 
12 CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM)
(a) Remove the EFI relay from the engine room junction block.
(b) Disconnect the E4 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance: 
(d) Reinstall the EFI relay.
(e) Reconnect the ECM connector.
13 CHECK HARNESS AND CONNECTOR (EFI RELAY - BODY GROUND)
(a) Check the harness and connector between the EFI relay and body ground.
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance : 
(2) Reinstall the EFI relay.
(3) Reconnect the ECM connector.
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI RELAY - BATTERY)
EVAP System
RELATED DTCS
If any EVAP system DTCs are set, the malfunctioning area can be determined
using the table below.
NOTICE:
If the 0.02 inch reference pressure difference between the ...
VC Output Circuit
DESCRIPTION
The ECM constantly uses 5 V from the battery voltages supplied to the +B
(BATT) terminal to operate the
microprocessor. The ECM also provides this power to the sensors through the VC
...
Other materials:
On-vehicle inspection
1. INSPECT MASS AIR FLOW METE
NOTICE:
Perform the mass air flow (MAF) meter inspection
by following the procedures below.
Only replace the MAF meter when the MAF value
in the DATA LIST (with the engine stopped) are
not within the normal operating range or there is
fore ...
Starting the engine
Check that the parking brake is set.
Check that the shift lever is set in P.
Firmly depress the brake pedal.
The engine switch indicator will turn green. If the indicator does not turn
green, the engine cannot be started.
Press the engine switch.
The engine will crank until it sta ...
Smart key system
The following operations can be performed simply by carrying
the electronic key on your person, for example in your pocket.
The driver should always carry the electronic key.
Locks and unlocks the doors
Front door handles
Sliding door handles
Back door
Starts and stops the ...
