Toyota RAV4 manuals

Toyota Sienna Service Manual: Front Occupant Classification Sensor LH Circuit Malfunction

DTC B1780 Front Occupant Classification Sensor LH Circuit Malfunction

DESCRIPTION

The front occupant classification sensor LH circuit consists of the occupant classification ECU and the front occupant classification sensor LH.

DTC B1780 is recorded when a malfunction is detected in the front occupant classification sensor LH circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1780

  • The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front occupant classification sensor LH circuit for 2 seconds.
  • Front occupant classification sensor LH malfunction
  • Occupant classification ECU malfunction
  • Front seat assembly RH (Front occupant classification sensor LH)
  • Occupant classification ECU
  •  Front seat wire RH

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK DTC

  1. Turn the ignition switch to the ON position.
  2.  Clear the DTCs stored in the memory.

    HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  3.  Turn the ignition switch to the LOCK position.
  4.  Turn the ignition switch to the ON position.
  5.  Check the DTCs (35).

OK: DTC B1780 is not output. HINT: Codes other than DTC B1780 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

2 CHECK CONNECTION OF CONNECTORS

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Check that the connectors are properly connected to the occupant classification ECU and the front occupant classification sensor LH.

OK: The connectors are properly connected

CONNECT CONNECTOR, THEN GO TO STEP 1

3 CHECK FRONT SEAT WIRE RH (SHORT TO B+)

CHECK FRONT SEAT WIRE RH (SHORT TO B+)

  1. Disconnect the connectors from the occupant classification ECU and the front occupant classification sensor LH.
  2.  Connect the negative (-) terminal cable to the battery.
  3.  Turn the ignition switch to the ON position.
  4.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE FRONT SEAT WIRE RH

4 CHECK FRONT SEAT WIRE RH (OPEN)

CHECK FRONT SEAT WIRE RH (OPEN)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Using a service wire, connect O5-1 (SVC1) and O5-3 (SGD1), and connect O5-2 (SIG1) and O5-3 (SGD1) of connector "C".

    NOTICE: Do not forcibly insert a service wire into the terminals of the connector when connecting.

  4.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FRONT SEAT WIRE RH

5 CHECK FRONT SEAT WIRE RH (SHORT)

 CHECK FRONT SEAT WIRE RH (SHORT)

  1. Disconnect the service wire from connector "C".
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FRONT SEAT WIRE RH

6 CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)

CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FRONT SEAT WIRE RH

7 CHECK DTC

  1. Connect the connectors to the occupant classification ECU and the front occupant classification sensor LH.
  2.  Connect the negative (-) terminal cable to the battery.
  3.  Turn the ignition switch to the ON position.
  4.  Clear the DTCs stored in the memory.

    HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position.
  7.  Check the DTCs (35).

OK: DTC B1780 is not output. HINT: Codes other than DTC B1780 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

8 REPLACE OCCUPANT CLASSIFICATION ECU

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the occupant classification ECU.

HINT: Perform the inspection using parts from a normal vehicle if possible.

9 PERFORM ZERO POINT CALIBRATION

  1. Connect the negative (-) terminal cable to the battery.
  2.  Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed.

Go to step 12

10 PERFORM SENSITIVITY CHECK

 

  1. Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

Go to step 12

11 CHECK DTC

  1. Turn the ignition switch to the ON position.
  2.  Clear the DTCs stored in the memory.

    HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  3.  Turn the ignition switch to the LOCK position.
  4.  Turn the ignition switch to the ON position.
  5.  Check the DTCs (35).

OK: DTC B1780 is not output. HINT: Codes other than DTC B1780 may be output at this time, but they are not related to this check.

END

12 REPLACE FRONT SEAT ASSEMBLY RH

  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the front seat assembly RH.

13 PERFORM ZERO POINT CALIBRATION

  1. Connect the negative (-) terminal cable to the battery.
  2.  Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed.

14 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

END

Passenger Side Buckle Switch Circuit Malfunction
DTC B1771 Passenger Side Buckle Switch Circuit Malfunction DESCRIPTION The passenger side buckle switch circuit consists of the occupant classification ECU and the front seat inner belt assembly ...

Front Occupant Classification Sensor RH Circuit Malfunction
DTC B1781 Front Occupant Classification Sensor RH Circuit Malfunction DESCRIPTION The front occupant classification sensor RH circuit consists of the occupant classification ECU and the front oc ...

Other materials:

Customizing vehicle features
Changing using the audio system screen Audio system with “CAR” button Press the “SETUP” button. Select “Vehicle” on the “Setup” screen. Audio system with “APPS” button Press the “APPS” button. Select “Setup” on the “Apps” screen and select ...

Removal
1. REMOVE REAR DOOR WINDOW FRAME MOULDING Remove the screw. Using a heat light, heat the rear door window frame moulding between 40 to 60 C (104 to 140 F). NOTICE: Do not heat the rear door window frame moulding excessively. Slide the rear door window frame moulding upward to r ...

Reassembly
1. INSTALL OVERDRIVE DIRECT CLUTCH O-RING (a) Coat an O-ring with ATF, and install it to the direct clutch drum. NOTICE: Make sure that the O-ring is not twisted or pinched when it is installed. 2. INSTALL OVERDRIVE DIRECT CLUTCH DRUM SUBASSEMBLY (a) Coat the direct clutch drum with A ...

© 2011-2024 Copyright www.tsienna.net