Toyota Sienna Service Manual: Front Occupant Classification Sensor RH Collision Detection

Toyota Sienna Service Manual / Supplemental restraint system / Occupant classification system / Diagnostic trouble code chart / Front Occupant Classification Sensor RH Collision Detection

DTC B1786 Front Occupant Classification Sensor RH Collision Detection

DESCRIPTION

DTC B1786 is output when the occupant classification ECU receives a collision detection signal sent by the front occupant classification sensor RH if an accident occurs.

DTC B1786 is also output when the front seat assembly RH is subjected to a strong impact, even if an actual accident does not occur.

However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1786 can be cleared by "Zero point calibration" and "Sensitivity check".

Therefore, if DTC B1786 is output, first perform "Zero point calibration" and "Sensitivity check".

DTC No.	DTC Detection Condition	Trouble Area
B1786	Front seat assembly RH malfunction Occupant classification ECU malfunction Front occupant classification sensor RH detected a large load	Front seat assembly RH (Front occupant classification sensor RH) Occupant classification ECU

INSPECTION PROCEDURE

1 PERFORM ZERO POINT CALIBRATION

Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed

2 PERFORM SENSITIVITY CHECK

Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb

3 CHECK DTC

Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
) Check the DTCs (35).

OK: DTC B1786 is not output. HINT: Codes other than DTC B1786 may be output at this time, but they are not related to this check.

4 REPLACE FRONT SEAT ASSEMBLY RH

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat assembly RH ( for flat type, SE-48 for manual seat, SE-58 for power seat).

HINT: Perform the inspection using parts from a normal vehicle if possible.

5 PERFORM ZERO POINT CALIBRATION

Connect the negative (-) terminal cable to the battery.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed.

6 PERFORM SENSITIVITY CHECK

Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

7 CHECK DTC

Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory.

HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (35).

OK: DTC B1786 is not output. HINT: Codes other than DTC B1786 may be output at this time, but they are not related to this check.

8 REPLACE OCCUPANT CLASSIFICATION ECU

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU

9 PERFORM ZERO POINT CALIBRATION

Connect the negative (-) terminal cable to the battery.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETED" is displayed.

10 PERFORM SENSITIVITY CHECK

Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

END

Front Occupant Classification Sensor LH Collision Detection

DTC B1785 Front Occupant Classification Sensor LH Collision Detection DESCRIPTION DTC B1785 is output when the occupant classification ECU receives a collision detection signal sent by the front ...

Rear Occupant Classification Sensor LH Collision Detection

DTC B1787 Rear Occupant Classification Sensor LH Collision Detection DESCRIPTION DTC B1787 is output when the occupant classification ECU receives a collision detection signal sent by the rear o ...

Other materials:

Maintenance requirements
To ensure safe and economical driving, day-to-day care and regular maintenance are essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance: General maintenance General maintenance should be performed on a daily basis. This can be done ...

Adjusting the set speed
To change the set speed, operate the lever until the desired set speed is displayed. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold the lever in the desired direction. In the vehicle-to-vehicl ...

Rear Air Conditioning Relay Circuit
DESCRIPTION The RR A/C relay is switched on by signals from the A/C amplifier. It supplies power to the rear blower motor. WIRING DIAGRAM INSPECTION PROCEDURE 1 INSPECT RELAY (RR A/C) (a) Remove the RR A/C relay from the No. 3 relay block. (b) Measure the resistance according to t ...