1 BASIC INSPECTION
2 INSPECT FUSE (ECU-B)
3 CHECK DTC
4 INSPECT COMMUNICATION FUNCTION OF LARGE-SCALE BODY MULTIPLEX COMMUNICATION SYSTEM (BEAN)
5 READ VALUE OF INTELLIGENT TESTER
OK (Power slide door ECU LH):
6 INSPECT POWER SLIDE DOOR MAIN SWITCH
Resistance
HINT: If the switch does not illuminate, it will not affect the ON / OFF function of the switch
7 CHECK WIRE HARNESS (POWER SLIDE DOOR MAIN SWITCH - POWER SLIDE DOOR ECU LH)
Resistance (Check for open circuit)
Resistance (Check for short circuit)
8 CHECK WIRE HARNESS (POWER SLIDE DOOR MAIN SWITCH - POWER SLIDE DOOR ECU RH)
Resistance (Check for open circuit)
Resistance (Check for open circuit)
9 READ VALUE OF INTELLIGENT TESTER
OK (Power slide door ECU RH):
REPLACE POWER SLIDE DOOR ECU LH
10 CHECK SWITCH OPERATION
HINT: If the power slide door cannot operate using the power slide door control switch even when the child lock is unlocked, there may be a malfunction in the child lock switch. In this case, check the handle switch circuit.
11 INSPECT SATELLITE SWITCH
Resistance
HINT: If the switch does not illuminate, it will not affect the ON / OFF function of the switch. For the illumination check, refer to SLIDE DOOR SYSTEM
12 CHECK WIRE HARNESS (SATELLITE SWITCH - DRIVER SIDE J/B, BODY GROUND)
Resistance (Check for open circuit)
Resistance (Check for open circuit)
REPAIR OR REPLACE HARNESS AND CONNECTOR
13 READ VALUE OF INTELLIGENT TESTER
OK (Power slide door ECU LH):
* "B PILLAR SW" appears on the display of the intelligent tester, however the name of the part corresponding to the display of the tester is "Power slide door control switch".
14 INSPECT POWER SLIDE DOOR CONTROL SWITCH LH
Resistance
HINT: If the switch does not illuminate, it will not affect the ON / OFF function of the switch. For the illumination check, refer to SLIDE DOOR SYSTEM
15 CHECK WIRE HARNESS (DOOR CONTROL SWITCH - POWER SLIDE DOOR ECU, BODY GROUND)
Resistance (Check for open circuit)
Resistance (Check for open circuit)
REPLACE POWER SLIDE DOOR ECU LH
16 READ VALUE OF INTELLIGENT TESTER
OK (Power slide door ECU LH):
17 INSPECT POWER SLIDE DOOR TOUCH SENSOR LH
Resistance
18 CHECK WIRE HARNESS (POWER SLIDE DOOR TOUCH SENSOR LH - POWER SLIDE DOOR ECU LH)
Resistance (Check for open circuit)
REPLACE POWER SLIDE DOOR ECU LH
19 READ VALUE OF INTELLIGENT TESTER
OK (Power slide door ECU LH):
20 INSPECT FUEL LID COURTESY SWITCH
Resistance
21 CHECK WIRE HARNESS (FUEL LID COURTESY SWITCH - DOOR ECU LH AND BODY GROUND)
Resistance (Check for open circuit)
Resistance (Check for open circuit)
REPLACE POWER SLIDE DOOR ECU LH
22 PERFORM ACTIVE TEST BY INTELLIGENT TESTER
HINT: During the ACTIVE TEST, the intelligent tester sends a signal to the power slide door ECU LH to drive the motor and clutch. If the motor and clutch operate, the motor and clutch itself and the wire harness between the motor and clutch and the power slide door ECU LH are considered to be functioning normally.
OK (Power slide door ECU LH):
23 INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY LH
OK
Resistance
Reference
HINT: A cycle of the pulse changes between approx. 10 to 20 msec. according to the speeds that the slide door is moving.
NOTICE: When disconnecting the control motor and clutch, initialize the power slide door system
24 CHECK WIRE HARNESS (POWER SLIDE DOOR CONTROL MOTOR - POWER SLIDE DOOR ECU LH)
Resistance (Check for open circuit)
REPLACE POWER SLIDE DOOR ECU LH
25 READ VALUE OF INTELLIGENT TESTER
OK (Power slide door ECU LH):
* "POLE" appears on the display of the intelligent tester, however the name of the part corresponding to the display of the tester is "pawl".
26 INSPECT POWER SLIDE DOOR LOCK ASSEMBLY LH
27 CHECK WIRE HARNESS (POWER SLIDE DOOR LOCK ASSEMBLY LH - POWER SLIDE DOOR ECU LH)
REPLACE POWER SLIDE DOOR ECU LH
28 PERFORM ACTIVE TEST BY INTELLIGENT TESTER
HINT: During the ACTIVE TEST, the intelligent tester sends a signal to the power slide door ECU LH to drive the release motor. If the release motor operates, the release motor itself and the wire harness between the release motor and power slide ECU LH are considered to be functioning normally.
OK (Power slide door ECU LH):
29 INSPECT SLIDE DOOR LOCK RELEASE MOTOR ASSEMBLY
OK
30 CHECK WIRE HARNESS (SLIDE DOOR LOCK RELEASE MOTOR LH - POWER SLIDE DOOR ECU LH)
Resistance (Check for open circuit)
Resistance (Check for open circuit)
31 REPLACE POWER SLIDE DOOR ECU LH
SYSTEM NORMAL
Reclining Motor Circuit
DESCRIPTION
The fold seat control ECU receives a switch operation signal from the power
rear no. 2 seat switch and
the fold seat switch, and activates the reclining motor. At this time, the Hall
IC (seatback position sensor)
detects the actuation of the seatback and sends a seatback actuation ...
Radio Receiver Power Source Circuit
DESCRIPTION
This circuit provides power to the radio receiver.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 INSPECT RADIO RECEIVER ASSEMBLY
Disconnect the radio receiver connector.
Measure the resistance according to the value in the
table below.
Standard resistance
Measure t ...
Outer mirror switch
Inspection
1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o
Memory)
The L side of the left / right adjustment switch:
Inspect the mirror switch resistance.
Standard resistance (Left side)
If the result is not as specified, replace the switch
assembly.
The R side of t ...