Toyota RAV4 manuals

Toyota Sienna Service Manual: Installation

HINT: Install the RH side by the same procedure as the LH side.

1. INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

(a) Install the rear disc brake cylinder mounting LH with the 2 bolts.

Torque: 88 N*m (900 kgf*cm, 65 ft.*lbf)

2. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

(a) Install the rear disc brake pad support plate (No. 1) and rear disc brake pad support plate (No. 2) to the rear disc brake cylinder mounting LH.

3. INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT

NOTICE: If necessary, replace the anti squeal shim kit when replacing the brake pad.

(a) Apply disc brake grease to each anti squeal shim No. 1.

(b) Install anti squeal shims No. 1 and anti squeal shim No. 2 on each pad.

4. INSTALL DISC BRAKE PAD KIT REAR (PAD ONLY)

(a) Install the brake pad kit rear to the rear disc brake cylinder mounting LH.

NOTICE: There should be no oil or grease on the friction surfaces of the pads and the disc.

5. INSTALL DISC BRAKE CYLINDER ASSEMBLY REAR LH

(a) Install the disc brake cylinder assembly rear LH with the 2 bolts.

Torque: 34 N*m (350 kgf*cm, 25 ft.*lbf)

6. CONNECT REAR LH FLEXIBLE HOSE

CONNECT REAR LH FLEXIBLE HOSE

(a) Using SST, Install the rear brake flexible hose.

SST 09023-12701 Torque: 23 N*m (235 kgf*cm, 17 ft.*lbf)

7. CONNECT REAR BRAKE TUBE NO.4

(a) Install the clip and connect the rear brake flexible hose.

CONNECT REAR BRAKE TUBE NO.4

(b) Using SST and a spanner, connect the rear brake tube No. 4.

SST 09023-00101 Torque: 15 N*m (155 kgf*cm, 11 ft.*lbf)

8. FILL RESERVOIR WITH BRAKE FLUID (See page BR- 3)

9. BLEED BRAKE MASTER CYLINDER (See page BR-3)

10. BLEED BRAKE LINE (See page BR-4)

11. BLEED BRAKE ACTUATOR (w/ VSC) (See page BR- 4)

12. CHECK FLUID LEVEL IN RESERVOIR (See page BR- 7)

13. CHECK BRAKE FLUID LEAKAGE

14. INSTALL REAR WHEEL Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf)

Reassembly
1. INSTALL REAR DISC (a) Aligning the matchmarks, install the rear disc. HINT: Select the installation position where the disc has the minimum runout. 2. INSPECT DISC RUNOUT (a) Temporarily ...

Rear drum brake
Components ...

Other materials:

ECU Power Source Circuit
DESCRIPTION The position control ECU and switch assembly (power seat control switch and ECU) is contained in the switch assembly. During manual operation, only one switch signal is accepted. If signals are input from 2 or more switches simultaneously, all of them are ignored, except when s ...

Gyro Error
DTC 58-10 Gyro Error DTC 80-10 Gyro Error DESCRIPTION DTC No. DTC Detection Condition Trouble Area 58-10 Ground short, power supply short, or open circuit in the gyro signal Gyro sensor Radio and navigation assembly 80-10 ...

Open in Pump Motor Circuit
DTC C1251/51 Open in Pump Motor Circuit DESCRIPTION The motor relay (semiconductor relay) is housed in the brake actuator assembly and drives the pump motor based on a signal from the skid control ECU. WIRING DIAGRAM Refer to DTCs C0273/13 and C0274/14 (See page BC-31). INSPECTION PROCED ...

В© 2011-2024 Copyright www.tsienna.net