Toyota Sienna Service Manual: Installation
1. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3
(a) Install the parking brake cable LH guide to the parking brake cable assembly No. 3.
(b) Connect the parking brake cable No. 3 to the parking brake cable equalizer.
(c) Install the parking brake cable No. 3 with the 3 bolts and button.
Torque: Bolt (A) 5.4 N*m (55 kgf*cm, 48 in.*lbf) Bolt (B) 8 N*m (82 kgf*cm, 71 in.*lbf)
2. CONNECT PARKING BRAKE CABLE ASSEMBLY NO.3
(a) Install the parking brake cable No. 3 with the 2 bolts to the backing plate.
Torque: 8 N*m (82 kgf*cm, 71 in.*lbf)
3. APPLY HIGH TEMPERATURE GREASE (for Drum Type) (See page BR-40)
4. INSTALL REAR BRAKE SHOE (for Drum Type) (See page BR-40)
5. INSTALL FRONT BRAKE SHOE (for Drum Type) (See page BR-40)
6. CHECK REAR DRUM BRAKE INSTALLATION (for Drum Type) (See page BR-42)
7. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)
8. ADJUST REAR DRUM BRAKE SHOE CLEARANCE (for Drum Type) (See page BR-42)
9. INSPECT PARKING BRAKE PEDAL TRAVEL (for Drum Type) (See page PB-1)
10. ADJUST PARKING BRAKE PEDAL TRAVEL (for Drum Type) (See page PB-1)
11. APPLY HIGH TEMPERATURE GREASE (for Disc Type) (See page PB-16)
12. INSTALL PARKING BRAKE SHOE ASSEMBLY LH NO.2 (for Disc Type) (See page PB-17)
13. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET (for Disc Type)
14. INSTALL PARKING BRAKE SHOE STRUT LH (for Disc Type)
15. INSTALL PARKING BRAKE SHOE ASSEMBLY LH NO.1 (for Disc Type) (See page PB-17)
16. CHECK PARKING BRAKE INSTALLATION (for Disc Type) (See page PB-18)
17. INSTALL REAR DISC (for Disc Type) (See page BR- 33)
18. ADJUST PARKING BRAKE SHOE CLEARANCE (for Disc Type) (See page PB-18)
19. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH (for Disc Type) (See page BR-35)
20. INSTALL REAR WHEEL Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf)
21. INSTALL PARKING BRAKE PEDAL TRAVEL (See page PB-1)
22. ADJUST PARKING BRAKE PEDAL TRAVEL (See page PB-1)
Removal
HINT:
For the parking brake cable assembly No. 2, perform the
same procedure to the parking brake cable assembly No. 3.
1. REMOVE REAR WHEEL
2. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for
Drum Type) ...
Parking brake assembly
COMPONENTS
...
Other materials:
Removal
1. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
2. REMOVE FRONT OUTER COWL TOP PANEL SUBASSEMBLY
3. DRAIN ENGINE COOLANT
4. REMOVE V-BANK COVER SUB-ASSEMBLY
5. REMOVE NO. 2 AIR CLEANER INLET
6. REMOVE NO. 1 AIR CLEANER INLET
7. REMOVE AIR CLEANER CAP SUB-ASSEMBLY
8. REMOVE AIR CLEANER CASE SUB-ASSE ...
Disassembly
1. REMOVE CENTER CLUSTER MODULE KNOB NO.1 (for Manual Air Conditioning
System)
(a) Remove the center cluster module knob No. 1.
2. REMOVE CENTER CLUSTER MODULE KNOB NO.2 (for Manual Air Conditioning
System)
(a) Release the 2 claws fittings and remove the center
cluster module knob No ...
Diagnosis system
1. CHECK BATTERY VOLTAGE
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge the battery before
proceeding.
2. CHECK DLC3
(a) The ECU uses the ISO 15765-4 for communication
protocol. The terminal arrangement of the DLC3
complies with SAE J1962 and matches the ISO
15765-4 f ...
