Toyota RAV4 manuals

Toyota Sienna Service Manual: Installation

1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

  1.  Install the front shoulder belt anchor adjuster assembly with the bolt.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

2. INSTALL CENTER PILLAR UPPER GARNISH

3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

INSTALL FRONT SEAT OUTER BELT ASSEMBLY

NOTICE: Do not disassemble the retractor.

  1.  Check the degree of tilt when beginning to lock the ELR.
  1.  Check that the belt does not lock within 15 degrees of tilt in all directions but that the belt locks with over 45 degrees of tilt, when gently moving the retractor.

    If operation is not as specified, replace the front seat outer belt assembly.

  1.  Install the retractor with the 2 bolts.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

  2.  Install the shoulder anchor with the nut.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

  3. Install the floor anchor with the bolt.

    Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)

  4.  Install the floor anchor cover.
  5.  Check the ELR lock.

NOTICE: The check should be performed with the assembly installed.

  1. Check that the belt locks when pulling out the belt quickly when the belt is installed.

    If operation is not as specified, replace the front seat outer belt assembly.

  1.  Check the fastening function of the child restraint system.

NOTICE: The check should be performed with the assembly installed.

  1.  Check that the belt cannot be pulled out any more but can be rewound after the belt is fully pulled out.
  2.  Check that the belt can be pulled out and rewound after the belt is fully rewound.

    If operation is not as specified, replace the front seat outer belt assembly.

4. INSTALL CENTER PILLAR LOWER GARNISH

5. INSTALL FRONT DOOR WEATHERSTRIP

6. INSTALL REAR DOOR WEATHERSTRIP

7. INSTALL FRONT DOOR SCUFF PLATE

8. INSTALL REAR DOOR SCUFF PLATE

9. INSTALL FRONT SEAT ASSEMBLY

HINT:

10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

11. PERFORM INITIALIZATION

HINT: Some systems need initialization when disconnecting the cable from the negative battery terminal

Removal
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait for 90 seconds after disconnecting the cable to prevent the airbag working 2. REMOVE FRONT SEAT ASSEMBLY HINT:  Refer to ...

Disposal
1. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN INSTALLED IN VEHICLE) NOTICE:  Never dispose of a front seat outer belt assembly with an deactivated pretensioner.  The seat belt ...

Other materials:

Operation flow
HINT: Perform troubleshooting in accordance with the procedures below. The following is an outline of basic troubleshooting procedures. Confirm the troubleshooting procedures for the circuit you are working on before beginning troubleshooting. VEHICLE BROUGHT TO WORKSHOP CUSTOMER PR ...

Installation
1. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2) (See page EC-39) 2. INSTALL FRONT EXHAUST PIPE ASSEMBLY (a) Install a new gasket to the front exhaust pipe assembly. (b) Install the front exhaust pipe assembly with the 2 nuts. Torque: 62 N*m (632 kgf*cm, 46 ft.*lbf) 3. V V(A) ins ...

Speaker Circuit
DESCRIPTION The sound signal that has been amplified by the stereo component amplifier is sent to the speakers from the stereo component amplifier through this circuit. If there is a short in this circuit, the stereo component amplifier detects it and stops output to the speakers. Thus s ...

В© 2011-2024 Copyright www.tsienna.net