Toyota Sienna Service Manual: Installation
1. INSTALL INSTRUMENT PANEL SAFETY PAD SUBASSEMBLY
- Using a torque wrench, install the bolt <B>.
Torque: 20 N*m (204 kgf*cm, 14 ft.*lbf)
2. INSTALL SHIFT LEVER ASSEMBLY
- Using a torque wrench, install the 4 bolts.
Torque: 21 N*m (214 kgf*cm, 12.6 ft.*lbf)
3. INSTALL DEFROSTER NOZZLE OPENING PLATE NO.1
4. INSTALL FRONT NO.2 SPEAKER ASSEMBLY
5. INSTALL FRONT NO.1 SPEAKER ASSEMBLY
6. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY NO.2
7. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
8. INSTALL FRONT PILLAR GARNISH RH
9. INSTALL FRONT PILLAR GARNISH LH
10. INSTALL INTEGRATION CONTROL & PANEL ASSEMBLY
11. INSTALL RADIO RECEIVER ASSEMBLY
12. INSTALL STEREO COMPONENT SPEAKER ASSEMBLY
13. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH
14. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY LOWER CENTER
15. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY CENTER
16. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING ASSEMBLY
17. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
18. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER NO.2
19. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER NO.1
20. INSTALL FLOOR CARPET COVER CENTER RH
21. INSTALL FLOOR CARPET COVER CENTER LH
22. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY NO.3
23. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY NO.1
24. INSTALL INSTRUMENT SIDE PANEL RH
25. INSTALL INSTRUMENT SIDE PANEL LH
26. INSTALL INSTRUMENT PANEL BOX NO.2
27. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
28. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
29. INSTALL INSTRUMENT PANEL SAFETY PAD INSERT SUB-ASSEMBLY NO.1
30. INSTALL INSTRUMENT PANEL FINISH PANEL SUBASSEMBLY LOWER LH
31. INSTALL COWL SIDE TRIM BOARD RH
32. INSTALL COWL SIDE TRIM BOARD LH
33. INSTALL FRONT DOOR SCUFF PLATE RH
34. INSTALL FRONT DOOR SCUFF PLATE LH
35. INSTALL COMBINATION METER ASSEMBLY
36. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
37. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY
38. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
39. INSTALL SPIRAL CABLE SUB-ASSEMBLY
40. INSTALL STEERING COLUMN COVER
41. ADJUST SPIRAL CABLE SUB-ASSEMBLY
42. INSTALL STEERING WHEEL ASSEMBLY
43. INSTALL HORN BUTTON ASSEMBLY
44. INSTALL STEERING WHEEL COVER LOWER NO.2
45. INSTALL STEERING WHEEL COVER LOWER NO.3
46. CONNECT BATTERY NEGATIVE TERMINAL
47. INSPECT HORN BUTTON ASSEMBLY
48. INSPECT SRS WARNING LIGHT
Reassembly
1. INSTALL INSTR PNL PASS L/DOOR AIR BAG
ASSEMBLY
2. INSTALL INSTRUMENT PANEL WIRE NO.2
3. INSTALL NAVIGATION ANTENNA ASSEMBLY
4. INSTALL ANTENNA CORD SUB-ASSEMBLY
5. INSTALL INSTRUMENT PANEL BOX ...
Seat belt
...
Other materials:
Turning on the high beam headlights
With the headlights on, push
the lever away from you to turn
on the high beams.
When the light switch is in
position, the Automatic High Beam
system will be activated.
Pull the lever toward you to the
center position to turn the high
beams off.
Pull the lever toward you and ...
Disposal
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
When scrapping a vehicle equipped with the SRS or
disposing of the curtain shield airbag assembly, be sure to
deploy the airbag first in accordance with the proce ...
Command list
Some recognizable voice commands and their actions are shown
below as examples.
Basic
Command
Action
“Help”
Prompts voice guidance to offer examples of commands
or operation methods
“Go Back”
Returns to the previous screen
Phone
...
