Toyota RAV4 manuals

Toyota Sienna Service Manual: On-vehicle inspection

1. Check battery electrolyte level

(a) Check the electrolyte level.

(1) If the electrolyte level is low, replace the battery (or add distilled water) and check the charging system.

2. CHECK BATTERY SPECIFIC GRAVITY

CHECK BATTERY SPECIFIC GRAVITY

(a) Check the color of the hydrometer.

Result

3. CHECK BATTERY VOLTAGE

(a) If it has not been 20 minutes since the vehicle was driven or since the engine was stopped, turn the ignition switch to the ON position and turn on the electrical systems (headlights, blower motor, rear defogger, etc.) for 60 seconds. This will remove the surface charge from the battery.

(b) Turn the ignition switch off and the electrical systems off.

(c) Measure the battery voltage between the negative (- ) and positive (+) terminals of the battery.

CHECK BATTERY VOLTAGE

Standard voltage: 12.5 to 12.9 V at 20°C (68°F)

HINT: If the voltage is below the specification, charge the battery.

4. CHECK BATTERY TERMINAL

(a) Check that the battery terminals are not loose or corroded.

If the terminals are corroded, clean them.

5. CHECK FUSES

(a) Measure the resistance of the ALT fuse, ALT-S fuse, GAUGE fuse and GAUGE 1 fuse.

Standard resistance: Below 1 Ω

If the result is not as specified, replace the fuses as necessary.

6. CHECK V-RIBBED BELT

(a) Check the belt for wear, cracks or other signs of damage.

If any of the following defects is found, replace the V-ribbed belt.

CHECK V-RIBBED BELT

(b) Check that the belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.

If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt correctly.

CHECK V-RIBBED BELT

7. INSPECT GENERATOR WIRING

(a) Visually check the generator wiring.

(1) Check that the wiring is in good condition.

8. CHECK FOR ABNORMAL NOISES

(a) Listen for abnormal noises from the generator.

(1) Check that no abnormal noises are heard from the generator while the engine is running.

9. CHECK CHARGE WARNING LIGHT CIRCUIT

(a) Turn the ignition switch to the ON position. Check that the charge warning light comes on.

(b) Start the engine and check that the light goes off.

If the light does not operate as specified, troubleshoot the charge warning light circuit.

10. INSPECT CHARGING CIRCUIT WITHOUT LOAD

 INSPECT CHARGING CIRCUIT WITHOUT LOAD

(a) Connect a voltmeter and ammeter to the charging circuit as follows.

(1) Disconnect the wire from terminal B of the generator, then connect it to the negative (-) lead of an ammeter.

(2) Connect the positive (+) lead of the ammeter to terminal B of the generator.

(3) Connect the positive (+) lead of a voltmeter to positive (+) terminal of the battery.

(4) Ground the negative (-) lead of the voltmeter.

(b) Check the charging circuit.

(1) Keep the engine speed at 2000 rpm and check the reading on the ammeter and voltmeter.

Standard amperage: 10 A or less

Standard voltage: 13.2 to 14.8 V

If the result is not as specified, replace the generator.

HINT: If the battery is not fully charged, the ammeter reading will sometimes be more than the standard amperage.

11. INSPECT CHARGING CIRCUIT WITH LOAD

(a) Keep the engine speed at 2000 rpm, turn on the high beam headlights, and turn the heater blower switch to the "HI" position.

(b) Check the reading on the ammeter.

Standard amperage: 30 A or more

If the ammeter reading is less than the standard amperage, replace the generator assembly.

HINT: If the battery is fully charged, the ammeter reading may be less than the standard amperage. In this case, increase electrical load by operating devices such as the wiper motor and rear window defogger.

Then, recheck the reading on the ammeter.

Precaution
1. Check that the battery cables are connected to the correct terminals. 2. Disconnect the battery cables when the battery is given a quick charge. 3. Do not perform tests with a high voltage ...

Charge Warning Light Comes ON while Driving
INSPECTION PROCEDURE 1 CHECK LOCK FUNCTION OF CLUTCH PULLEY (a) Check the lock function with the pulley installed in the vehicle. (1) Visually check that the rotor in the generator operates wit ...

Other materials:

Stereo component amplifier
COMPONENTS Removal 1. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY 2. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY  Disconnect the connectors.  Remove the 2 nuts and the stereo component amplifier assembly. Installation 1. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY ...

Installation
1. INSTALL SPIRAL CABLE  Check that the front wheels are facing straight ahead.  Set the turn signal switch to the neutral position. NOTICE: If it is not in the neutral position, the pin of the turn signal switch may snap. Install the spiral cable. NOTICE: When ...

Bluetooth tel check mode
HINT: Illustration may differ from the actual vehicle depending on the device settings and options. Therefore, some detailed area may not be shown exactly the same as on the actual vehicle. 1. ENTER DIAGNOSTIC MODE 2. BLUETOOTH TEL CHECK  Select "Bluetooth TEL Check" fro ...

© 2011-2024 Copyright www.tsienna.net