Toyota RAV4 manuals

Toyota Sienna Service Manual: Open in Driver Side Squib 2nd Step Circuit

DTC B1181/18 Open in Driver Side Squib 2nd Step Circuit

DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1181/18 is recorded when an open circuit is detected in the driver side squib 2nd step circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1181/18

  • Open circuit in D2+ wire harness or D2- wire harness of driver side squib 2nd step
  • Driver side squib 2nd step malfunction
  • Spiral cable malfunction
  • Center airbag sensor assembly malfunction
  • Steering pad (Driver side squib 2nd step)
  •  Spiral cable
  •  Center airbag sensor assembly
  •  Instrument panel wire

INSPECTION PROCEDURE

HINT:

1 CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the steering pad.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable.

CAUTION: Never connect a tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B1181/18 is not output. HINT: Codes other than DTC B1181/18 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE STEERING PAD

2 CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

 CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the spiral cable.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 4

3 CENTER AIRBAG SENSOR ASSEMBLY

CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the steering pad and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B1181/18 is not output.

HINT: Codes other than DTC B1181/18 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

4 CHECK INSTRUMENT PANEL WIRE

 CHECK INSTRUMENT PANEL WIRE

  1. Disconnect the instrument panel wire connector from the spiral cable.
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

5 CHECK SPIRAL CABLE

CHECK SPIRAL CABLE

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE SPIRAL CABLE

USE SIMULATION METHOD TO CHECK

Short in Driver Side Squib 2nd Step Circuit
DTC B1180/17 Short in Driver Side Squib 2nd Step Circuit DESCRIPTION The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. ...

Short to GND in Driver Side Squib 2nd Step Circuit
DTC B1182/19 Short to GND in Driver Side Squib 2nd Step Circuit DESCRIPTION The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering ...

Other materials:

Reassembly
1. INSTALL LH REAR BUMPER SIDE RETAINER Install the LH rear bumper side retainer with the 3 screws. 2. INSTALL RH REAR BUMPER SIDE RETAINER Install the RH rear bumper side retainer with the 3 screws. 3. INSTALL REAR BUMPER REINFORCEMENT SUBASSEMBLY Install the rear bumper reinf ...

GCWR, TWR and Unbraked TWR
Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. GCWR* 2WD models: 8900 lb. (4037 kg) AWD models: 8990 lb. (4078 kg) TWR* 3500 lb. (1588 kg) Unbraked TWR* 1000 lb. (454 kg) *: These models ...

Removal
1. REMOVE REAR WHEEL 2. REMOVE TAIL EXHAUST PIPE ASSEMBLY (See page EX-8) 3. SEPARATE REAR SPEED SENSOR (a) Remove the bolt and the speed sensor from the axle carrier. NOTICE: Be careful not to damage the speed sensor Prevent foreign matter from adhering to the speed sensor. 4. REMO ...

В© 2011-2024 Copyright www.tsienna.net