Toyota Sienna Service Manual: Open in Front Passenger Side Squib 2nd Step Circuit

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Open in Front Passenger Side Squib 2nd Step Circuit

DTC B1186/58 Open in Front Passenger Side Squib 2nd Step Circuit

DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1186/58 is recorded when an open circuit is detected in the front passenger side squib 2nd step circuit.

DTC No.	DTC Detecting Condition	Trouble Area
B1186/58	Open circuit in P2+ wire harness or P2- wire harness of front passenger side squib 2nd step Front passenger side squib 2nd step malfunction Center airbag sensor assembly malfunction	Front passenger airbag assembly (Front passenger side squib 2nd step) Center airbag sensor assembly Instrument panel wire

INSPECTION PROCEDURE

HINT:

Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)

CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the front passenger airbag assembly.
Connect the black wire side of SST (resistance 2.1 Ω) to the instrument panel wire.

CAUTION: Never connect a tester to the front passenger airbag assembly (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B1186/58 is not output. HINT: Codes other than DTC B1186/58 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2 CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT)

CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB 2ND STEP

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST (resistance 2.1 Ω) from the instrument panel wire.
Disconnect the connector from the center airbag sensor assembly.
Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B1186/58 is not output. HINT: Codes other than DTC B1186/58 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short in Front Passenger Side Squib 2nd Step Circuit

DTC B1185/57 Short in Front Passenger Side Squib 2nd Step Circuit DESCRIPTION The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front passenge ...

Short to GND in Front Passenger Side Squib 2nd Step Circuit

DTC B1187/55 Short to GND in Front Passenger Side Squib 2nd Step Circuit DESCRIPTION The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front p ...

Other materials:

Fuel pump shut off system
To minimize the risk of fuel leakage when the engine stalls or when an airbag inflates upon collision, the fuel pump shut off system stops the supply of fuel to the engine. Follow the procedure below to restart the engine after the system is activated. Vehicles without a smart key system ...

Disassembly
1. REMOVE FRONT DIFFERENTIAL RING GEAR (a) Place matchmarks on the front differential ring gear and differential case. (b) Remove the 14 bolts. (c) Using a plastic hammer, tap on the front differential ring gear to remove it from the case. 2. REMOVE FRONT DIFFERENTIAL CASE FRONT TA ...

Master Reset/ Voice Processing Device ON Error
DTC 01-DD Master Reset DTC 01-E1 Voice Processing Device ON Error DESCRIPTION HINT: *1: This code may be stored if the engine is started and the ignition switch is turned to START position again. *2: Even if no fault is present, this trouble code may be stored depending on the battery ...