Toyota RAV4 manuals

Toyota Sienna Service Manual: Open in Front Passenger Side Squib Circuit

DTC B0106/54 Open in Front Passenger Side Squib Circuit

DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0106/54 is recorded when an open circuit is detected in the front passenger side squib circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B0106/54

  • Open circuit in P+ wire harness or P- wire harness of front passenger side squib
  •  Front passenger side squib malfunction
  •  Center airbag sensor assembly malfunction
  • Front passenger airbag assembly (Front passenger side squib)
  •  Center airbag sensor assembly
  •  Instrument panel wire

INSPECTION PROCEDURE

HINT:

1 CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front passenger airbag assembly.
  4.  Connect the black wire side of SST (resistance 2.1 Ω) to the instrument panel wire.

CAUTION: Never connect a tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs

OK: DTC B0106/54 is not output. HINT: Codes other than DTC B0106/54 may be output at this time, but they are not related to this check.

Go to step 2

 REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2 CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the instrument panel wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B0106/54 is not output. HINT: Codes other than code B0106/54 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short in Front Passenger Side Squib Circuit
DTC B0105/53 Short in Front Passenger Side Squib Circuit DESCRIPTION The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly. ...

Short to GND in Front Passenger Side Squib Circuit
DTC B0107/51 Short to GND in Front Passenger Side Squib Circuit DESCRIPTION The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag as ...

Other materials:

Other functions
Switching between outside air and recirculated air modes Press . The mode switches between outside air mode ( appears on the display) and recirculated air mode ( appears on the display) each time the button is pressed. Defogging the windshield Defoggers are used to defog the windshield a ...

Terminals of ECU
1. CHECK DRIVER SIDE J/B ASSEMBLY (MULTIPLEX NETWORK BODY ECU)  Disconnect the B6, 1C, 1K and 1L J/B connectors. Measure the voltage and resistance according to the value(s) in the table below. HINT: If the result is not as specified, there may be a malfunction on the w ...

Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)
DESCRIPTION Shifting from 1st to 5th is performed in combination with "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, SL3, S4 and SR which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM cont ...

В© 2011-2024 Copyright www.tsienna.net