Toyota Sienna Service Manual: Open in Rear Curtain Shield Squib RH Circuit

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Open in Rear Curtain Shield Squib RH Circuit

DTC B1631/84 Open in Rear Curtain Shield Squib RH Circuit

DESCRIPTION

The rear curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1631/84 is recorded when an open circuit is detected in the rear curtain shield squib RH circuit.

DTC No.	DTC Detecting Condition	Trouble Area
B1631/84	Open circuit in ICR+ wire harness or ICR- wire harness of rear curtain shield squib RH Rear curtain shield squib RH malfunction Center airbag sensor assembly malfunction	Curtain shield airbag assembly RH (Rear curtain shield squib RH) Center airbag sensor assembly Floor wire No. 2

INSPECTION PROCEDURE

HINT:

Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (REAR CURTAIN SHIELD SQUIB RH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (REAR CURTAIN SHIELD SQUIB RH)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the curtain shield airbag assembly RH.
Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire No. 2.

CAUTION: Never connect a tester to the curtain shield airbag assembly RH (Rear curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs

OK: DTC B1631/84 is not output.

HINT: Codes other than DTC B1631/84 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH

2 CHECK FLOOR WIRE NO.2 (REAR CURTAIN SHIELD SQUIB RH CIRCUIT)

CHECK FLOOR WIRE NO.2 (REAR CURTAIN SHIELD SQUIB RH CIRCUIT)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST (resistance 2.1 Ω) from the floor wire No. 2.
Disconnect the connector from the center airbag sensor assembly.
Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE NO.2

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

Connect the connectors to the curtain shield airbag assembly RH and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B1631/84 is not output. HINT: Codes other than DTC B1631/84 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short in Rear Curtain Shield Squib RH Circuit

DTC B1630/83 Short in Rear Curtain Shield Squib RH Circuit DESCRIPTION The rear curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembl ...

Short to GND in Rear Curtain Shield Squib RH Circuit

DTC B1632/81 Short to GND in Rear Curtain Shield Squib RH Circuit DESCRIPTION The rear curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag ...

Other materials:

Check for intermittent problems
1. CHECK FOR INTERMITTENT PROBLEMS HINT: For use of the intelligent tester only: Inspect the vehicle's ECM using check mode. Intermittent problems are easier to detect with an intelligent tester when the ECM is in check mode. In check mode, the ECM uses 1 trip detection logic, which is more ...

Intake Air Temperature Circuit/ Intake Air Temperature Circuit Low Input/ Intake Air Temperature Circuit High Input
DTC P0110 Intake Air Temperature Circuit DTC P0112 Intake Air Temperature Circuit Low Input DTC P0113 Intake Air Temperature Circuit High Input DESCRIPTION The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in ther ...

Display check mode
HINT: This mode checks the color display on the display. Illustrations may differ from the actual vehicle depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle. 1. ENTER DIAGNOSTIC MODE 2. D ...