Toyota RAV4 manuals

Toyota Sienna Service Manual: Power slide door control motor and clutch

Toyota Sienna Service Manual / Engine hood / door / Power slide door control motor and clutch

INSPECTION

1. INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY LH

INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY LH

  1. Remove the motor and clutch.
  2. Connect the battery positive (+) lead to terminal 3 and the battery negative (-) lead to terminal 2.
  3. Apply battery voltage to the terminals and check the motor operation.

OK

INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY LH

If the result is not as specified, replace the motor and clutch.

  1. Check the resistance of the terminals.

Resistance

INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY LH

If the result is not as specified, replace the motor and clutch.

INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY LH

  1. Reinstall the motor and clutch with the connector connected.
  2. Check the pulse of the pulse sensor.
  1. Using an oscilloscope, check the pulse generated when the door is manually opened and closed.

Reference

INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY LH

If the result is not as specified, replace the motor and clutch.

HINT: The cycle of the pulse changes between approx. 10 to 20 msec. according to the speeds that the slide door is moving.

2. REMOVE SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH

REMOVE SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH

  1. Remove the motor and clutch.
  2. Connect the battery positive (+) lead to terminal 3 and the battery negative (-) lead to terminal 2.
  3. Apply battery voltage to the terminals and check the motor operation.

OK

REMOVE SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH

If the result is not as specified, replace the motor and clutch.

  1. Check the resistance of the terminals.

Resistance

REMOVE SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH

If the result is not as specified, replace the motor and clutch.

REMOVE SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH

  1. Reinstall the motor and clutch with the connector connected.
  2. Check the pulse of the pulse sensor.
  1. Using an oscilloscope, check the pulse generated when the door is manually opened and closed.

Reference

REMOVE SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH

If the result is not as specified, replace the motor and clutch.

HINT: The cycle of the pulse changes between approx. 10 to 20 msec. according to the speeds that the slide door is moving.

Disposal
HINT: On the RH side, use the same procedures as on the LH side. 1. DISPOSE OF BACK DOOR STAY SUB-ASSEMBLY LH Horizontally fix the stay in a vise with the piston-rod pulled out. Wearing ...

Power slide door
COMPONENTS ...

Other materials:

Disassembly
1. REMOVE REAR SEAT LEG COVER LH  Remove the 2 screws and seat leg cover. 2. REMOVE REAR SEAT LEG COVER RH  Remove the 2 screws and seat leg cover. 3. REMOVE REAR SEAT LEG SIDE COVER LH  Remove the 2 screws and seat leg side cover. 4. REMOVE LH SEAT REAR SEAT LOCK ...

Display Panel does not Open, Tilt or Tilts Improperly
INSPECTION PROCEDURE 1 CHECK RADIO AND NAVIGATION ASSEMBLY Check for foreign matter or obstructions caught in the moving parts of the panel. OK: No obstruction or foreign matter found. 2 CHECK OPERATION Check if the navigation and audio systems function properly. OK: Naviga ...

DTC check / clear
1. DTC CHECK (USING SST CHECK WIRE)  Check the DTCs (Present trouble code).  Turn the ignition switch ON, and wait for approximately 60 seconds.  Using SST, connect terminals TC and CG of the DLC3. SST 09843-18040 NOTICE: Connect the terminals to the correct p ...

В© 2011-2024 Copyright www.tsienna.net