Toyota Sienna Service Manual: Power Slide Door Pulse Sensor Malfunction on
Rear Right Door
DTC B2223 Power Slide Door Pulse Sensor Malfunction on
Rear Right Door
DESCRIPTION
- A pulse sensor is built into slide door RH for jam and foreign
object detection and for slide door position
detection. The jam and foreign object detection feature of the pulse sensor
monitors the operating
speed of the slide door while the power slide door is in operation. The
slide door position detection
feature of the pulse sensor monitors where the slide door is. If the slide
door position detection feature
outputs a pulse signal that is out of the normal range, the power slide door
ECU RH will set DTC
B2223.
- If DTC B2223 is set, the power slide door system will be turned
off. Thus, the slide door can be moved
freely and will be switched to manual operation mode (not electrically
controlled).
- In order to restore the power slide door system to normal
operation mode, first solve the problem
indicated by DTC B2223 and then manually close the slide door fully (reset
operation).
DTC No. |
DTC Detection Condition |
Trouble Area |
B2223 |
Power slide door RH does not operate |
- Wire harness
- Power slide door control motor and clutch RH
- Power slide door ECU RH
|
WIRING DIAGRAM
INSPECTION PROCEDURE
1 CHECK WIRE HARNESS (MOTOR AND CLUTCH RH - POWER SLIDE DOOR ECU RH)
- Disconnect the P22 motor and clutch, and P27 ECU
connectors.
- Check the resistance between the wire harness side
connectors.
Resistance (Check for open circuit)
2 INSPECT SLIDE DOOR CONTROL MOTOR AND CLUTCH ASSEMBLY RH
- Remove the motor and clutch.
- Connect the battery positive (+) lead to terminal 3 and
battery negative (-) terminal lead to terminal 2.
- Apply battery voltage to the terminals and check the
motor operation.
OK
- Check the resistance of the clutch terminals.
Resistance
- Reinstall the motor and clutch with the connector
connected.
- Check the pulse of the pulse sensor.
- Using an oscilloscope, check the pulse generated
when the door is manually opened and closed.
Reference
HINT:
A cycle of the pulse changes between approx. 10 to
20 msec. according to the speeds that the slide door
is moving.
NOTICE:
When disconnecting the control motor and
clutch, initialize the power slide door system.
REPLACE POWER SLIDE DOOR ECU RH
If a malfunction code is displayed during the DTC check,
check the circuit listed for that code in the table below.
(Proceed to the page given for that circuit.)
POWER SLIDE DOOR SYSTEM
...
DTC B2224 Power Slide Door Pulse Sensor Malfunction on
Rear Left Door
DESCRIPTION
A pulse sensor is built into slide door LH for jam and foreign
object detection and for slide door posi ...
Other materials:
Seat heaters
For driver’s seat
For front passenger’s seat
On
The indicator light comes on.
Adjusts the seat temperature
The further you move the dial
upward, the warmer the seat
becomes.
The seat heaters can be used when the engine switch is in the “ON”
position
(vehicles ...
License plate light assembly
COMPONENTS
REMOVAL
1. REMOVE BACK DOOR GARNISH CENTER
2. REMOVE BACK DOOR SIDE GARNISH LH
3. REMOVE BACK DOOR SIDE GARNISH RH
4. REMOVE BACK DOOR STRAP COVER
5. REMOVE BACK DOOR PULL STRAP
6. REMOVE BACK DOOR TRIM BOARD ASSEMBLY
7. REMOVE BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE
8. RE ...
Communication Error from ECM to Distance
Control ECU
DTC P1616 Communication Error from ECM to Distance
Control ECU
DTC U0100 Lost Communication with ECM/PCM "A"
DESCRIPTION
The ECM receives signals from each sensor and ECU, then sends signals such as
A/T signals, cruise
control operation signals, low speed operation signals, brake co ...