Toyota RAV4 manuals

Toyota Sienna Service Manual: Power Slide Door RH does not Operate When Using Inside / Outside Handle

Toyota Sienna Service Manual / Engine hood / door / Power slide door system / Inspection procedure / Power Slide Door RH does not Operate When Using Inside / Outside Handle

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

1 OPERATION CHECK

  1. If the power slide door does not operate when trying to open it, proceed to A.
  2.  If the power slide door does not operate when trying to close it, proceed to B.

2 CHECK SLIDE DOOR CLOSER SYSTEM

  1. Check if the slide door closer system operates.

3 READ VALUE OF INTELLIGENT

  1. Using the intelligent tester, check the DATA LIST for proper functioning of the handle operation detect switch.

OK (Power slide door ECU RH):

Power slide door ECU RH

4 INSPECT SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY RH (HANDLE OPERATION DETECT SWITCH)

INSPECT SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY RH

  1. Inspect the resistance of the switch.

Resistance

Resistance

5 CHECK WIRE HARNESS (SLIDE DOOR LOCK REMOTE CONTROL - POWER SLIDE DOOR ECU RH)

CHECK WIRE HARNESS

  1. Disconnect the S23 remote control and P27 ECU connectors.
  2. Check the resistance between the wire harness side connectors.

Resistance (Check for open circuit)

Check for open circuit

  1. Check the resistance between the S23 remote control connector and body ground.

Resistance (Check for open circuit)

Check for open circuit

REPLACE POWER SLIDE DOOR ECU RH

6 READ VALUE OF INTELLIGENT TESTER

  1. Using the intelligent tester, check the DATA LIST for proper functioning of the child protection detect switch.

OK (Power slide door ECU RH):

Power slide door ECU RH

7 INSPECT SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY RH (CHILD PROTECTION DETECT SWITCH)

INSPECT SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY RH

  1. Inspect the resistance of the switch.

Resistance

Resistance

8 CHECK WIRE HARNESS (SLIDE DOOR LOCK REMOTE CONTROL - POWER SLIDE DOOR ECU RH)

CHECK WIRE HARNESS

  1. Disconnect the S23 switch and P27 ECU connectors.
  2.  Check the resistance between the wire harness side connectors.

Resistance (Check for open circuit)

Check for open circuit

  1. Check the resistance between the S23 switch connector and body ground.

Resistance (Check for open circuit)

Check for open circuit

REPLACE POWER SLIDE DOOR ECU RH

Power Slide Door LH does not Operate When Using Inside / Outside Handle
DESCRIPTION  The inside / outside handles have the ability to control operation of the power slide door. Pulling either handle transmits a request signal to the power slide door ECU LH, ...

Jam Protection Function Activates During Power Slide Door LH Operation
DESCRIPTION  It may be caused by ill-fitting slide door, faulty touch sensor or faulty pulse sensor.  The power slide door ECU activates the slide motor to open / close the power ...

Other materials:

Third outside seats
To use Pull the head restraints up. To fold Press the button Removing the head restraints Front and second outside seats Pull the head restraint up while pressing the lock release button. Second center* and third center seats Pull the head restraint up while pressi ...

Oxygen (A/F) Sensor Heater Control Circuit Low/ Oxygen (A/F) Sensor Heater Control Circuit High
DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) DTC P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) DTC P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 S ...

Child restraint systems with a top tether strap (second seat)
Secure the child restraint system using the seat belt or LATCH anchors, and adjust the head restraint to the uppermost position. *: Ottoman seat only Latch the hook onto the anchor bracket and tighten the top tether strap. Make sure the top tether strap is secure ...

В© 2011-2024 Copyright www.tsienna.net