Toyota Sienna Service Manual: Rear Airbag Sensor LH Circuit Malfunction
DTC B1155/39 Rear Airbag Sensor LH Circuit Malfunction
DESCRIPTION
The rear airbag sensor LH circuit consists of the center airbag sensor
assembly and rear airbag sensor
LH.
If the center airbag sensor assembly receives signals from the rear airbag
sensor LH, it judges whether or
not the SRS should be activated.
DTC B1155/39 is recorded when a malfunction is detected in the rear airbag
sensor LH circui
DTC No. |
DTC Detecting Condition |
Trouble Area |
B1155/39 |
- The center airbag sensor assembly receives a line
short circuit signal, an open circuit signal, a short
circuit to ground signal or a short circuit to B+ signal
in the rear airbag sensor LH circuit for 2 seconds.
- Rear airbag sensor LH malfunction
- Center airbag sensor assembly malfunction
|
- Rear airbag sensor LH
- Center airbag sensor assembly
- Floor wire
|
WIRING DIAGRAM
INSPECTION PROCEDURE
1 CHECK DTC
- Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
- Clear the DTCs stored in memory (5).
- Turn the ignition switch to the LOCK position.
- Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
- Check the DTCs (5).
OK:
DTC B1155/39 is not output.
HINT:
Codes other than code B1155/39 may be output at this
time, but they are not related to this check.
Go to step 2
USE SIMULATION METHOD TO CHECK
2 CHECK CONNECTION OF CONNECTORS
- Turn the ignition switch to the LOCK position.
- Disconnect the negative (-) terminal cable from the
battery, and wait for at least 90 seconds.
- Check that the connectors are properly connected to the
center airbag sensor assembly and the rear airbag
sensor LH.
OK:
The connectors are connected.
CONNECT CONNECTORS
3 CHECK FLOOR WIRE (OPEN)
- Disconnect the connectors from the center airbag sensor
assembly and the rear airbag sensor LH.
- Using a service wire, connect A20-14 (VUCL) and A20-
13 (ESCL) of connector "B".
NOTICE:
Do not forcibly insert a service wire into the
terminals of the connector when connecting.
- Measure the resistance according to the value(s) in the
table below.
Standard resistance
- Using a service wire, connect A20-15 (CSL+) and A20-1
(CSL-) of connector "B".
NOTICE:
Do not forcibly insert a service wire into the
terminals of the connector when connecting.
- Measure the resistance according to the value(s) in the
table below.
Standard resistance
REPAIR OR REPLACE FLOOR WIRE
4 CHECK FLOOR WIRE (SHORT TO B+)
- Disconnect SST from connector "B".
- Connect the negative (-) terminal cable to the battery,
and wait for at least 2 seconds.
- Turn the ignition switch to the ON position.
- Measure the voltage according to the value(s) in the
table below.
Standard voltage
REPAIR OR REPLACE FLOOR WIRE
5 CHECK FLOOR WIRE (SHORT TO GROUND)
- Turn the ignition switch to the LOCK position.
- Disconnect the negative (-) terminal cable from the
battery, and wait for at least 90 seconds.
- Measure the resistance according to the value(s) in the
table below.
Standard resistance
REPAIR OR REPLACE FLOOR WIRE
6 CHECK FLOOR WIRE (SHORT)
- Measure the resistance according to the value(s) in the
table below.
Standard resistance
REPAIR OR REPLACE FLOOR WIRE
7 CHECK REAR AIRBAG SENSOR LH
- Connect the connector to the center airbag sensor
assembly.
- Interchange the rear airbag sensor RH with LH and
connect the connectors to them.
- Connect the negative (-) terminal cable to the battery,
and wait for at least 2 seconds.
- Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
- Clear the DTCs stored in memory (5).
- Turn the ignition switch to the LOCK position.
- Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
- Check the DTCs (5).
Result
HINT:
Codes other than DTC B1154/38 and B1155/39 may be
output at this time, but they are not related to this check.
REPLACE REAR AIRBAG SENSOR LH
REPLACE CENTER AIRBAG SENSOR
ASSEMBLY
USE SIMULATION METHOD TO CHECK
DTC B1154/38 Rear Airbag Sensor RH Circuit Malfunction
DESCRIPTION
The rear airbag sensor RH circuit consists of the center airbag sensor
assembly and rear airbag sensor
RH.
If the center airb ...
DTC B1160/83 Short in Curtain Shield Squib RH Circuit
DESCRIPTION
The curtain shield squib RH circuit consists of the center airbag sensor
assembly and the curtain shield
airbag assembly RH.
T ...
Other materials:
Door Courtesy Switch Circuit
DESCRIPTION
The Multiplex network body ECU detects the condition of the door courtesy
switch assembly.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 READ VALUE OF INTELLIGENT TESTER
Connect the intelligent tester to DLC3.
Turn the ignition switch to ON and push the intelligent
tester ...
Passenger Airbag ON/OFF Indicator Circuit
Malfunction
DTC B1152/28 Passenger Airbag ON/OFF Indicator Circuit
Malfunction
DESCRIPTION
The passenger airbag ON/OFF indicator circuit consists of the center airbag
sensor assembly and
passenger airbag ON/OFF indicator.
This circuit indicates the operation condition of the front passenger airbag, ...
Transfer
SST
RECOMMENDED TOOLS
EQUIPMENT
LUBRICANT
SSM
...