Toyota RAV4 manuals

Toyota Sienna Service Manual: Reassembly

1. INSTALL REAR SEAT STAY SUB-ASSEMBLY

  1.  Install the seat stay sub-assembly with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

2. INSTALL NO. 2 SEAT CUSHION SPRING ASSEMBLY RH

3. INSTALL LOCUS CABLE RH

  1.  Install the locus cable RH with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

4. INSTALL NO. 2 SEAT CUSHION COVER SUBASSEMBLY RH

 INSTALL NO. 2 SEAT CUSHION COVER SUBASSEMBLY RH

  1.  Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly RH to the seat cushion pad with new hog rings.

NOTICE:

5. INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY

  1. Install the rear seat lock release strap assembly with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

6. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO. 2 RH

  1.  Install the reclining adjuster release handle No. 2 RH with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

7. INSTALL RECLINING RELEASE HANDLE SUBASSEMBLY RH

  1.  Install the reclining release handle sub-assembly RH with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

8. INSTALL REAR SEAT BACK CONNECTING RH WIRE

  1.  Install the rear seat back connecting RH wire.

9. INSTALL NO. 2 SEATBACK COVER RH

INSTALL NO. 2 SEATBACK COVER RH

  1.  Using hog ring pliers, install the No. 2 seatback cover RH to the seatback pad with new hog rings.

NOTICE:

  1. Install the 2 headrest supports.

10. INSTALL NO. 2 SEATBACK LOCK CONTROL BEZEL

  1.  Install the No. 2 seatback lock control bezel with the screw.

11. INSTALL NO. 2 REAR SEAT COVER BEZEL

  1.  Install the No. 2 rear seat cover bezel with 3 screws.

12. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY INNER RH

  1. Install the No. 2 rear seat belt assembly inner RH with the bolt.

    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)

13. INSTALL REAR SEATBACK ASSEMBLY RH

  1.  Install the rear seatback assembly RH with the 4 bolts.

    Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf)

14. INSTALL LH SEAT REAR SEAT RECLINING COVER

INSTALL LH SEAT REAR SEAT RECLINING COVER

  1.  Install the LH seat rear seat reclining cover with 2 screws.

15. INSTALL RH SEAT REAR SEAT RECLINING COVER

INSTALL RH SEAT REAR SEAT RECLINING COVER

  1.  Install the RH seat rear seat reclining cover with 2 screws.
Disassembly
1. REMOVE RH SEAT REAR SEAT RECLINING COVER  Remove the 2 screws.  Remove the RH seat rear seat reclining cover by pulling it out in the arrow mark direction shown in the illus ...

Installation
1. INSTALL REAR NO. 2 SEAT ASSEMBLY RH  Place the rear No. 2 seat assembly RH in the cabin. NOTICE: Be careful not to damage the body.  Install the seat with the bolt. Torque: ...

Other materials:

Installation
1. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3 (a) Install the parking brake cable LH guide to the parking brake cable assembly No. 3. (b) Connect the parking brake cable No. 3 to the parking brake cable equalizer. (c) Install the parking brake cable No. 3 with the 3 bolts and button. T ...

Control Module Performance
DTC P0607 Control Module Performance DESCRIPTION The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from the CPUs are different and deviate from the standards, the ECM will illuminate the MIL and set a DTC immediately ...

Memory recall function
Each electronic key can be registered to recall your preferred driving position. Registering procedure Record your driving position to button “1” or “2” before performing the following: Carry only the key you want to register, and then close the driver’s door. If 2 or more keys ar ...

© 2011-2024 Copyright www.tsienna.net