Toyota RAV4 manuals

Toyota Sienna Service Manual: Reassembly

1. INSTALL INPUT SHAFT OIL SEAL RING

INSTALL INPUT SHAFT OIL SEAL RING

(a) Compress a new input shaft oil seal ring from both sides to reduce dimension A.

Dimension A: 5 mm (0.197 in.)

(b) Coat the oil seal ring with ATF and install it to the input shaft.

NOTICE: Do not expand the end gap of the oil seal ring too much. Fix the hooks firmly.

2. INSTALL FORWARD CLUTCH PISTON SUBASSEMBLY

INSTALL FORWARD CLUTCH PISTON SUBASSEMBLY

(a) Coat the forward clutch piston with ATF, and install it to the input shaft.

NOTICE: Be careful not to damage the lip of the forward clutch piston.

3. INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

(a) Install the return spring to the input shaft.

NOTICE: Installing the spring sub-assembly, check that all of the springs are fit in the piston correctly.

(b) Coat the clutch balancer with ATF.

INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

(c) Install the clutch balancer to the input shaft.

NOTICE:

INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

(d) Place SST on the clutch balancer, and compress the clutch balancer with a press.

SST 09387-00020

(e) Install the snap ring with a snap ring expander.

(f) Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

NOTICE:

(g) Set the end gap of the snap ring in the piston as shown in the illustration.

NOTICE: The end gap of the snap ring should not align with any of the stoppers.

4. INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

(a) Coat the 5 discs with ATF.

INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

(b) Install the 5 plates, 5 discs and flange input shaft.

NOTICE: Make sure that the plates, discs, and flange are installed as shown in the illustration.

INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

(c) Using a screwdriver, install the snap ring.

(d) Check that the end gap of the snap ring is not aligned with one of the cutouts.

NOTICE: The snap ring should be fully engaged in the groove of the drum.

5. INSPECT PACK CLEARANCE OF FORWARD CLUTCH

HINT: (See page AX-243)

6. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

HINT: (See page AX-243)

Inspection
1. INSPECT PACK CLEARANCE OF FORWARD CLUTCH (a) Install the forward clutch on the oil pump. NOTICE: Be careful not to damage the oil seal ring of oil pump. b) Using a dial indicator, measure ...

Direct clutch
Components ...

Other materials:

Terminals of ECU
1. TELEVISION CAMERA ASSEMBLY  Disconnect the T10 camera connector Measure the voltage and resistance of each terminal of the wire harness side connector. If the result is not as specified, there may be a malfunction on the wire harness side.  Reconnect the T10 ...

Camshaft Position "B" Actuator Circuit
DESCRIPTION The Variable Valve Timing (VVT) system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine ...

Installation
1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY  Install the front shoulder belt anchor adjuster assembly with the bolt. Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf) 2. INSTALL CENTER PILLAR UPPER GARNISH 3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY NOTICE: Do not disassemble ...

В© 2011-2024 Copyright www.tsienna.net