Toyota RAV4 manuals

Toyota Sienna Service Manual: Reassembly

1. INSTALL UNDERDRIVE CLUTCH DRUM O-RING

INSTALL UNDERDRIVE CLUTCH DRUM O-RING

(a) Coat a new O-ring with ATF, and install it to the underdrive clutch drum.

NOTICE: Make sure that the O-ring is not twisted or pinched.

2. INSTALL UNDERDRIVE CLUTCH PISTON SET

 INSTALL UNDERDRIVE CLUTCH PISTON SET

(a) Coat the underdrive clutch piston with ATF, and install it to the underdrive clutch piston drum.

NOTICE:

3. INSTALL UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

INSTALL UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

(a) Install the return spring to the underdrive clutch drum.

NOTICE: Installing the spring sub-assembly, check that all of the springs are fit in the piston correctly.

(b) Coat the clutch balancer with ATF.

INSTALL UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

(c) Install the clutch balancer to the underdrive clutch drum.

NOTICE: Be careful not to damage the lip of the clutch balancer.

INSTALL UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

(d) Place SST on the clutch balancer and compress the piston return spring with a press.

SST 09350-32014 (09351-32070)

(e) Using a snap ring expander, install the snap ring to the underdrive clutch drum.

(f) Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

NOTICE:

INSTALL UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

(g) Set the end gap of the snap ring in the underdrive clutch drum as shown in the illustration.

NOTICE: The end gap of the snap ring should not align with any of the stoppers.

4. INSTALL UNDERDRIVE CLUTCH DISC NO.1

 INSTALL UNDERDRIVE CLUTCH DISC NO.1

(a) Coat the 4 discs with ATF.

(b) Install the 4 plates, 4 discs and flange to the underdrive clutch drum.

NOTICE: Make sure that the plates, discs, and flange are installed as shown in the illustration.

5. INSTALL 1ST & REVERSE BRAKE RETURN SPRING SHAFT SNAP RING

INSTALL 1ST & REVERSE BRAKE RETURN SPRING SHAFT SNAP RING

(a) Using a screwdriver, install the underdrive clutch flange No.2 hole snap ring.

(b) Check that the end gap of snap ring is not aligned with one of the cutouts.

NOTICE: The snap ring should be fully engaged in the groove of the drum.

6. INSPECT UNDERDRIVE PACK CLEARANCE

HINT: (See page AX-262)

Inspection
1. INSPECT UNDERDRIVE PACK CLEARANCE (a) Install the underdrive clutch to the transaxle case. NOTICE: Be careful not to damage the oil seal rings. (b) Install a dial indicator as shown in the ...

Differential case
COMPONENTS ...

Other materials:

Evaporative Emission Control System Leak Detected
DTC P0455 Evaporative Emission Control System Leak Detected (Gross Leak) DTC P0456 Evaporative Emission Control System Leak Detected (Very Small Leak) DTC SUMMARY DESCRIPTION The circuit description can be found in the EVAP (Evaporative Emission) System. INSPECTION PROCEDURE Refer to t ...

Removal
1. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY (for 8-Passenger) HINT: Refer to the instructions for disassembly of the rear No. 1 seat assembly (for center seat).  Remove the bolt and rear seat 3 point type belt assembly. 2. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY (for 7-Pas ...

Message Settings
Display the “Phone/Message Settings” screen. Select “Messaging Settings”. Select the desired item to be set. Set automatic message transfer on/off. Set automatic message readout on/off. Set the SMS/MMS notification popup on/off. Set the e-mail notification pop ...

© 2011-2024 Copyright www.tsienna.net