Toyota RAV4 manuals

Toyota Sienna Service Manual: Registration

Toyota Sienna Service Manual / 2GR-FE Engine control system / SFI system / Registration

NOTICE: The Vehicle Identification Number (VIN) must be input into the replacement ECM.

HINT: The VIN is a 17-digit alphanumeric vehicle identification number. The intelligent tester is required to register the VIN.

1. INPUT INSTRUCTIONS

  1.  The general VIN input instructions using the intelligent tester are shown below:
  2.  The arrow buttons (UP, DOWN, RIGHT and LEFT) and numerical buttons (0 to 9) are used to input the VIN.
  3.  Cursor Operation To move the cursor around the tester screen, press the RIGHT and LEFT buttons.
  4.  Alphabetical Character Input
  1.  Press the UP and DOWN buttons to select the desired alphabetical character.
  1.  Numerical Character Input
  1.  Press the numerical button corresponding to the number that you want to input.

HINT: Numerical characters can be selected by using the UP and DOWN buttons.

  1.  Correction
  1.  When correcting the input character(s), put the cursor onto the character using the RIGHT and LEFT buttons.
  2. Select or input the correct character using the UP and DOWN buttons, or the numerical buttons.
  1.  Finishing Input Operation
  1.  Make sure that the input VIN matches the vehicle VIN after input.
  2.  Press the ENTER button on the tester.

2. READ VIN (Vehicle Identification Number)

  1.  The VIN reading process is shown in the flowchart below. Reading the VIN stored in the ECM is necessary when comparing it to the VIN provided with the vehicle.
  2.  Read the VIN using the intelligent tester.
  3.  Check the vehicle's VIN.
  4.  Connect the intelligent tester to the DLC3.
  5.  Turn the ignition switch to the ON position.
  6.  Turn the tester ON.
  7. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / VIN.

READ VIN

3. WRITE VIN

  1.  The VIN writing process is shown in the flowchart below. This process allows the VIN to be input into the ECM. If the ECM is changed, or the ECM VIN and Vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.
  2.  Write VIN using the intelligent tester.
  3.  Connect the intelligent tester to the DLC3.
  4.  Turn the ignition switch to the ON position.
  5.  Turn the tester ON.
  6. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / VIN.

WRITE VIN

WRITE VIN

WRITE VIN

Basic inspection
When a malfunction is not confirmed by the DTC check, troubleshooting should be carried out in all circuits considered to be possible causes of the problem. In many cases, by carrying out the basic ...

Checking monitor status
The purpose of the monitor result (mode 06) is to allow access to the results for on-board diagnostic monitoring tests of specific components/systems that are not continuously monitored. Examples a ...

Other materials:

Selecting, fast-forwarding and reversing tracks/files/songs
Selecting a track/file/song Press the “” or “” button on “SEEK•TRACK” or turn the “TUNE•SCROLL” knob to select the desired track/file/song number. To fast-forward or reverse, press and hold the “” or “” button on “SEEK•TRACK”. ...

Initialization
Items to initialize The following items must be initialized for normal system operation after such cases as the battery being reconnected, or maintenance being performed on the vehicle. Item When to initialize Power sliding door (if equipped) After reconnecting o ...

Removal
HINT: Don't use the dropped or damaged yawrate sensor Free from the foreign matters between yaerate sensor bracket and body. Make sure the sensor direction. 1. REMOVE FRONT SEAT ASSEMBLY RH HINT: See page SE-40. 2. REMOVE FRONT DOOR SCUFF PLATE RH 3. REMOVE COWL SIDE TRIM BOARD RH ...

© 2011-2024 Copyright www.tsienna.net