Toyota Sienna Service Manual: Removal
1. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
2. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
3. REMOVE FRONT PILLAR GARNISH LH
4. REMOVE FRONT PILLAR GARNISH RH
5. REMOVE VISOR ASSEMBLY LH
6. REMOVE VISOR ASSEMBLY RH
7. REMOVE ASSIST GRIP SUB-ASSEMBLY (2)
8. REMOVE VISOR HOLDER (1)
9. REMOVE ROOF CONSOLE BOX ASSEMBLY
10. REMOVE SUN ROOF OPENING TRIM MOULDING (W/ SLIDING ROOF)
11. REMOVE INNER REAR VIEW MIRROR ASSEMBLY
12. REMOVE ROOF HEADLINING ASSEMBLY (4)
13. REMOVE FRONT WIPER ARM HEAD CAP
14. REMOVE FRONT WIPER ARM LH
15. REMOVE FRONT WIPER ARM RH
16. REMOVE FRONT FENDER TO COWL SIDE SEAL LH
17. REMOVE FRONT FENDER TO COWL SIDE SEAL RH
18. REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY
19. REMOVE WINDSHIELD MOULDING OUTER UPPER
- Using a knife, cut off the moulding, as shown in the
illustration.
NOTICE: Do not damage the vehicle body with the knife.
- Remove the remaining moulding.
HINT: When removing, make a partial a cut, then pull and remove it by hand.
- w/ Deicer: Disconnect the connector, as shown in the illustration.
20. REMOVE WINDSHIELD GLASS
- Pass a piano wire between the vehicle body and glass from the interior.
- Tie both wire ends to wooden blocks or similar objects.
HINT: Apply protective tape to the outer surface of the vehicle body to prevent its surface from being scratched.
NOTICE:
- When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
- To prevent the safety pad from being scratched when removing the glass, place a plastic sheet between the piano wire and safety pad.
- Cut off the adhesive by pulling piano wire around the glass.
- Disengage the stoppers.
- Using a suction cup, remove the glass.
NOTICE: Leave as much adhesive on the vehicle body as possible when removing the glass.
21. CLEAN WINDSHIELD GLASS
- Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
- Clean the outer circumference of the glass with white gasoline.
NOTICE: Do not touch the glass surface after cleaning it.
Windshield glass
COMPONENTS
...
Installation
1. INSTALL WINDSHIELD GLASS NO.2 STOPPER
Coat the installation part of the stoppers with Primer
G.
NOTICE:
Allow the primer coating to dry for 3 minutes
or more.
...
Other materials:
Brake fluid
Bleeding
HINT:
If any work is performed on the brake system or if air in the
brake lines is suspected, bleed the air out of the brake
system.
NOTICE:
Wash the brake fluid off immediately if it adheres to any
painted surfaces.
1. REMOVE COWL TOP PANEL SUB-ASSEMBLY
OUTER FRONT (See page SP-13 ...
Short to B+ in Front Pretensioner Squib LH Circuit
DTC B0138/72 Short to B+ in Front Pretensioner Squib LH Circuit
DESCRIPTION
The front pretensioner squib LH circuit consists of the center airbag sensor
assembly and the front seat
outer belt assembly LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
DTC B01 ...
Disassembly
1. REMOVE COOLER THERMISTOR NO.1 (for Automatic Air Conditioning System)
(a) Disengage the 2 claw fittings and the clamp and
remove the cooler thermistor No. 1.
2. REMOVE COOLING UNIT MOTOR SUB-ASSEMBLY WITH FAN
(a) Remove the 3 screws and the cooling unit motor
sub-assembly w/ fan.
3. ...
