Toyota RAV4 manuals

Toyota Sienna Service Manual: Removal

HINT: On the RH side, use the same procedures as on the LH side.

1. REMOVE SLIDE DOOR

REMOVE SLIDE DOOR

  1. Remove the rear door scuff plate (See page IR-7).
  2. Remove the back door scuff plate (See page ED- 214).
  3. Remove the quarter trim panel (See page IR-9).
  4. Remove the upper rail cushion from the rail.
  5. Disconnect the 2 connectors from the body side and remove the bolt and wire.

REMOVE SLIDE DOOR

  1. Open the quarter glass.
  2. Using a screwdriver, disengage the clip and 2 claws, remove the rail end moulding.

HINT: Tape the screwdriver tip before use.

REMOVE SLIDE DOOR

  1. Remove the 2 bolts and bracket center No. 2 together with the tensioner (color: white).
  2. Remove the tensioner from the bracket center No.

    2.

REMOVE SLIDE DOOR

  1. Remove the 2 bolts and bracket center No. 1 together with the tensioner (color: black).
  2. Remove the tensioner from the bracket center No.

    1.

REMOVE SLIDE DOOR

  1. Remove the 2 nuts and open stop.

REMOVE SLIDE DOOR

  1. Rotate the base of the slide door roller lower in the direction indicated by arrow in the illustration and then remove the roller from the cut area of the lower rail from the body side.

REMOVE SLIDE DOOR

  1. Move the slide door rearward and then remove the slide door roller upper from the cut area in the rear part of the slide door rail upper.

REMOVE SLIDE DOOR

  1. Move the slide door further rearward and then remove the slide door hinge center from the rear part of the slide door rail center. Then, remove the slide door.

2. REMOVE SLIDE DOOR RAILS

  1. Remove the roof headlining (See page IR-6).
  2. Remove the 2 bolts, 2 nuts and the rail upper.
  3. Remove the 2 screws and rear side rail.
  4. Remove the 3 screws and rail center

3. REMOVE SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY LH

REMOVE SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY LH

  1. Disconnect the 2 cables.
  2. Remove the 2 bolts and full open stop lock.

4. REMOVE SLIDE DOOR ROLLER ASSEMBLY LOWER LH

REMOVE SLIDE DOOR ROLLER ASSEMBLY LOWER LH

  1. Remove the 3 bolts and roller.

5. REMOVE SLIDE DOOR HINGE ASSEMBLY CENTER LH

REMOVE SLIDE DOOR HINGE ASSEMBLY CENTER LH

  1. Remove the 3 bolts and hinge.
  2. LH side: Remove the cover.

6. REMOVE SLIDE DOOR ROLLER ASSEMBLY UPPER

  1. Remove the 2 bolts and roller.
Power slide door
COMPONENTS ...

Disassembly
1. REMOVE REAR DOOR WINDOW FRAME MOULDING REAR LH (See page ET-31) 2. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH (See page ET-32) 3. REMOVE SLIDE DOOR WINDOW GARNISH LH Fully o ...

Other materials:

Release Actuator Circuit
DESCRIPTION The fold seat control ECU receives a switch operation signal from the fold seat switch and activates the release actuator. The release actuator releases the lock of the stowed seat based on a drive voltage received from the ECU. WIRING DIAGRAM INSPECTION PROCEDURE 1 INSPECT ...

Installation
1. INSTALL NO. 2 REAR SEAT OUTER BELT ASSEMBLY NOTICE: Do not disassemble the retractor.  Check the degree of tilt when the No. 2 rear seat outer belt assembly begins to lock the ELR.  Check that the belt does not lock within 15 of tilt in all directions but that the be ...

Installation
1. INSTALL YAW RATE AND DECELERATION SENSOR (a) Connect the yawrate sensor connector. (b) Install the yawrate sensor with the 2 bolts. Torque: 13 N*m (136 kgf*cm, 10 ft.*lbf) 2. INSTALL COWL SIDE TRIM BOARD RH (a) Install the nut with the cowl side trim board plate RH. 3. INSTALL FRONT ...

В© 2011-2024 Copyright www.tsienna.net