HINT: On the LH side, use the same procedures as on the RH side.
1. REMOVE FRONT DOOR SCUFF PLATE RH
HINT: Tape the screwdriver tip before use.
2. REMOVE FRONT DOOR SCUFF PLATE LH
3. REMOVE REAR DOOR SCUFF PLATE RH
HINT: Tape the screwdriver tip before use.
4. REMOVE REAR DOOR SCUFF PLATE LH
5. REMOVE COWL SIDE TRIM BOARD RH
HINT: Tape the screwdriver tip before use.
6. REMOVE COWL SIDE TRIM BOARD LH
7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
9. REMOVE REAR DOOR WEATHERSTRIP RH
HINT: When reinstalling the weatherstrip, completely remove the sealer adhering to the opening flange on the body side beforehand.
10. REMOVE REAR DOOR WEATHERSTRIP LH
HINT: When reinstalling the weatherstrip, completely remove the sealer adhering to the opening flange on the body side beforehand.
11. REMOVE CENTER PILLAR GARNISH LOWER RH
HINT: Tape the screwdriver tip before use.
12. REMOVE CENTER PILLAR GARNISH LOWER LH
13. REMOVE CENTER PILLAR GARNISH UPPER RH
HINT: Tape the screwdriver tip before use.
HINT: Tape the screwdriver tip before use.
14. REMOVE CENTER PILLAR GARNISH UPPER LH
HINT: Use the same procedures described above for the RH side.
15. REMOVE BACK DOOR WEATHERSTRIP
16. REMOVE BACK DOOR SCUFF PLATE
HINT: Tape the screwdriver tip before use
17. REMOVE QUARTER TRIM PANEL ASSEMBLY FRONT RH
HINT: Tape the screwdriver tip before use.
18. REMOVE QUARTER TRIM PANEL ASSEMBLY FRONT LH
19. REMOVE ROOF HEADLINING GARNISH REAR
HINT: Tape the screwdriver tip before use.
20. REMOVE RR WINDOW SIDE GARNISH ASSEMBLY NO.2 RH
HINT: Tape the screwdriver tip before use.
HINT: Tape the screwdriver tip before use.
21. REMOVE RR WINDOW SIDE GARNISH ASSEMBLY NO.2 LH
HINT: Tape the screwdriver tip before use.
22. REMOVE RR WINDOW SIDE GARNISH ASSEMBLY RH
HINT: Tape the screwdriver tip before use.
HINT: Tape the screwdriver tip before use.
23. REMOVE RR WINDOW SIDE GARNISH ASSEMBLY LH
24. REMOVE FRONT PILLAR GARNISH RH
HINT: Tape the screwdriver tip before use.
HINT: Tape the screwdriver tip before use.
NOTICE: Cover the curtain shield airbag with the protection cover as soon as the pillar garnish is removed.
25. REMOVE FRONT PILLAR GARNISH LH
26. REMOVE RH VISOR ASSEMBLY
HINT: Tape the screwdriver tip before use.
27. REMOVE LH VISOR ASSEMBLY
28. REMOVE VISOR HOLDER
29. REMOVE ROOF CONSOLE BOX ASSEMBLY
30. REMOVE ASSIST GRIP SUB-ASSEMBLY
HINT: Tape the screwdriver tip before use.
31. REMOVE ROOF CONSOLE BOX
32. REMOVE AIR CONDITIONING NO.2 CONTROL ASSEMBLY
HINT: Tape the screwdriver tip before use.
33. REMOVE AIR OUTLET REGISTER ASSEMBLY NO.1
HINT: Tape the screwdriver tip before use.
34. REMOVE AIR OUTLET REGISTER ASSEMBLY NO.2
35. REMOVE AIR DUCT REGISTER ASSEMBLY NO.3
36. REMOVE AIR OUTLET REGISTER ASSEMBLY NO.4
37. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
38. REMOVE ROOF HEADLINING ASSEMBLY
NOTICE: In order to prevent the roof headlining from becoming bent, work must be performed by 2 or more persons when removing/installing it
Pressure Control Solenoid "C" Performance (Shift
Solenoid Valve SL3)
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gear
position (1st, 2nd, 3rd, 4th
or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory
to detect mechanical
troubles of the shift solenoid valves and valve bo ...
Freeze frame data
1. FREEZE FRAME DATA
(a) The vehicle (sensor) status, stored during ABS and/
or VSC operation or at the time of an error code
detection, can be displayed by the intelligent tester.
(b) Only one record of freeze frame data is stored and
the freeze frame data generated during ABS and/or
VSC op ...
Installation
1. INSTALL RADIO NO. 2 BRACKET
Install radio No. 2 bracket with the 4 screws.
2. INSTALL RADIO NO. 1 BRACKET
Install radio No. 1 bracket with the 4 screws.
3. INSTALL RADIO RECEIVER
Connect the connector.
Install the radio receiver with the 4 scr ...