Toyota RAV4 manuals

Toyota Sienna Service Manual: Seat Belt Buckle Switch LH Circuit Malfunction

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Seat Belt Buckle Switch LH Circuit Malfunction

DTC B0126/27 Seat Belt Buckle Switch LH Circuit Malfunction

DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and the front seat inner belt assembly LH.

DTC B0126/27 is recorded when a malfunction is detected in the seat belt buckle switch LH circuit

DTC No.

DTC Detecting Condition

Trouble Area

B0126/27
  • The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.
  • Front seat inner belt assembly LH malfunction
  • Center airbag sensor assembly malfunction
  • Front seat inner belt assembly LH (Seat belt buckle switch LH)
  •  Center airbag sensor assembly
  •  Floor wire

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

1 CHECK DTC

CHECK DTC

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  2.  Clear the DTCs stored in memory (5).
  3.  Turn the ignition switch to the LOCK position.
  4.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  5.  Check the DTCs (5).

OK: DTC B0126/27 is not output. HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

Go to step 2

USE SIMULATION METHOD TO CHECK

2 CHECK CONNECTION OF CONNECTORS

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly LH.

OK: The connectors are connected.

CONNECT CONNECTORS

3 CHECK VEHICLE

  1. Check the front driver seat type.

Result

Result

Go to step 11

 

4 CHECK FLOOR WIRE (OPEN)

CHECK FLOOR WIRE (OPEN)

  1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.
  2.  w/ Side airbag: Using a service wire, connect A20-19 (LBE+) and A20-2 (LBE-) of connector "B".

    NOTICE: Do not forcibly insert a service wire into the terminals of the connector when connecting.

  3.  w/o Side airbag: Using a service wire, connect A20-11 (LBE+) and A20-6 (LBE-) of connector "B".

    NOTICE: Do not forcibly insert a service wire into the terminals of the connector when connecting.

  4.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

5 CHECK FLOOR WIRE (SHORT TO B+)

Check floor wire (short to b+)

  1. Disconnect the service wire from connector "B".
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position.
  4.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE FLOOR WIRE

6 CHECK FLOOR WIRE (SHORT TO GROUND)

CHECK FLOOR WIRE (SHORT TO GROUND)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Measure the resistance according to the value(s) in the table below.

Standard resistance

CHECK FLOOR WIRE (SHORT TO GROUND)

REPAIR OR REPLACE FLOOR WIRE

7 CHECK FLOOR WIRE (SHORT)

CHECK FLOOR WIRE (SHORT)

  1. Measure the voltage according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

8 CHECK FRONT SEAT INNER BELT ASSEMBLY LH

CHECK FRONT SEAT INNER BELT ASSEMBLY LH

  1. Connect the connectors to the front seat inner belt assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B0126/27 is not output. HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

Go to step 9

USE SIMULATION METHOD TO CHECK

9 REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the front seat inner belt assembly LH.

HINT: Perform the inspection using parts from a normal vehicle if possible.

10 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6. Check the DTCs (5).

OK: DTC B0126/27 is output. HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

END

11 CHECK FLOOR WIRE (OPEN)

CHECK FLOOR WIRE (OPEN)

  1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.
  2. w/ Side airbag: Using a service wire, connect A20-19 (LBE+) and A20-2 (LBE-) of connector "B".

    NOTICE: Do not forcibly insert a service wire into the terminals of the connector when connecting.

  3.  w/o Side airbag: Using a service wire, connect A20-11 (LBE+) and A20-6 (LBE-) of connector "B".

    NOTICE: Do not forcibly insert a service wire into the terminals of the connector when connecting.

  4.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

12 CHECK FLOOR WIRE (SHORT TO B+)

CHECK FLOOR WIRE (SHORT TO B+)

  1. Disconnect the service wire from connector "B".
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position.
  4.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE FLOOR WIRE

13 CHECK FLOOR WIRE (SHORT TO GROUND)

CHECK FLOOR WIRE (SHORT TO GROUND)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

14 CHECK FLOOR WIRE (SHORT)

CHECK FLOOR WIRE (SHORT)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

15 CHECK FRONT SEAT INNER BELT ASSEMBLY LH

CHECK FRONT SEAT INNER BELT ASSEMBLY LH

  1. Connect the connectors to the front seat inner belt assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B0126/27 is not output. HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

Go to step 16

USE SIMULATION METHOD TO CHECK

16 REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the front seat inner belt assembly LH.

HINT: Perform the inspection using parts from a normal vehicle if possible.

17 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B0126/27 is not output. HINT: Codes other than code B0126/27 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

END

Short to B+ in Side Squib LH Circuit
DTC B0118/46 Short to B+ in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH (side squib LH). ...

Short in Front Pretensioner Squib RH Circuit
DTC B0130/63 Short in Front Pretensioner Squib RH Circuit DESCRIPTION The front pretensioner squib RH circuit consists of the center airbag sensor assembly and the front seat outer belt assembly ...

Other materials:

Reassembly
1. BEARING POSITION 2. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE (a) Install the differential gear lube apply tube and transaxle apply tube clamp with the bolt to the transaxle housing. Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf) NOTICE: Make sure to insert the pipe to the s ...

Problem symptoms table
HINT:  Use the table below to help determine the cause of the problem symptom. The likely causes of the problem are indicated in descending order. Check each suspected area in order. Repair or replace faulty parts or perform adjustments as necessary.  Inspect the fuse and rel ...

Screen Flicker or Color Distortion
INSPECTION PROCEDURE 1 CHECK DISPLAY SETTING Enter the display adjustment screen by pressing the "DISPLAY" switch.  Reset display settings (contrast, brightness) and check that the screen appears normal Press the "INFO" switch and then select "S ...

В© 2011-2024 Copyright www.tsienna.net