Toyota RAV4 manuals

Toyota Sienna Service Manual: Shift lock system

On-vehicle inspection

1. CHECK SHIFT LOCK OPERATION

(a) Move the shift lever to the P position.

(b) Turn the ignition switch to the LOCK position.

(c) Check that the shift lever cannot be moved to any position other than P.

(d) Turn the ignition switch to the on position, depress the brake pedal and check that the shift lever can be moved to another position. If operation can not be done as specified, inspect the shift lock control unit.

2. CHECK SHIFT LOCK RELEASE BUTTON OPERATION

(a) Using a small screwdriver, remove the shift lock release cover.

(b) When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position other than P.

If operation can not be done as specified, check the shift lever assembly installation condition.

3. CHECK KEY INTERLOCK OPERATION

(a) Turn the ignition switch to the ON position.

(b) Depress the brake pedal and move the shift lever to any position other than P.

(c) Check that the ignition key cannot be turned to the LOCK position.

(d) Move the shift lever to the P position, turn the ignition key to the LOCK position and check that the ignition key can be removed.

If operation cannot be done as specified, inspect the shift lock control unit.

4. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY

 INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY

(a) Measure the voltage according to the value(s) in the table below.

HINT: Do not disconnect the shift lock control unit assembly connector.

Voltage

Voltage

Voltage

Voltage

(b) Measure the resistance according to the value(s) in the table below.

HINT: Do not disconnect the shift lock control unit assembly connector.

If operation cannot be done as specified, replace the shift lever assembly.

Resistance

Resistance

5. INSPECT KEY INTER LOCK SOLENOID

INSPECT KEY INTER LOCK SOLENOID

(a) Disconnect the solenoid connector.

(b) Connect KLS+ (4) terminal to the batteries' positive (+) terminal and KLS (3) terminal to the battery negative (-) terminal, and apply about 12 V between KLS+ - KLS- terminals.

(c) Check that operation noise can be heard from the solenoid.

If the solenoid does not operate, replace the solenoid.

6. INSPECT SHIFT LOCK SOLENOID

INSPECT SHIFT LOCK SOLENOID

(a) Disconnect the solenoid connector.

(b) Connect SSL+ (2) terminal to the batteries' positive (+) terminal, and SLS- (1) terminal to the battery negative (-) terminal, and apply about 12 V between SLL+-SLS- terminals.

(c) Check that operation noise can be heard from the solenoid.

If the solenoid does not operate, replace the solenoid.

Installation
1. Install transmission valve body assembly (a) Install the shift solenoid valve SL1 to the valve body assembly with the bolt. Torque: 6.6 N*m (67 kgf*cm, 58 in.*lbf) (b) Install the shi ...

Shift lever
Components ...

Other materials:

DVD-ROM Abnormal
DTC 44-43 DVD-ROM Abnormal DESCRIPTION DTC No. DTC Detecting Condition Trouble Area 44-43 DVD-ROM operation is abnormal. DVD Television display assembly INSPECTION PROCEDURE HINT: After the inspection is completed, clear the ...

Terminals of ECU
1. CHECK POWER BACK DOOR ECU Disconnect the P13 and P14 ECU connectors, and check the voltage or resistance of each terminal of the wire harness side connectors If the result is not as specified, there may be a malfunction on the wire harness side. Reconnect the ECU connector ...

Rear Occupant Classification Sensor LH Circuit Malfunction
DTC B1782 Rear Occupant Classification Sensor LH Circuit Malfunction DESCRIPTION The rear occupant classification sensor LH circuit consists of the occupant classification ECU and the rear occupant classification sensor LH. DTC B1782 is recorded when a malfunction is detected in the rear oc ...

В© 2011-2024 Copyright www.tsienna.net