Toyota RAV4 manuals

Toyota Sienna Service Manual: Shift Solenoid "E" Control Circuit

Shift Solenoid "E" Control Circuit

DESCRIPTION

Shifting from 1st to 5th is performed in combination with "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, SL3, S4 and SR which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Fail safe function).

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid valves "ON/OFF" (In case of an open or short circuit, the ECM stops sending current to the circuit.) (See page AX-30).

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

COMPONENT OPERATING RANGE

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

1 INSPECT TRANSMISSION WIRE (SR)

INSPECT TRANSMISSION WIRE (SR)

(a) Disconnect the transmission wire connector from the transaxle.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance

2 CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

(a) Connect the transmission wire connector to the transaxle.

(b) Disconnect the connector from the ECM.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance

REPLACE ECM

3 INSPECT SHIFT SOLENOID VALVE SR

INSPECT SHIFT SOLENOID VALVE SR

(a) Remove the shift solenoid valve SR.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance

(c) Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

OK: The solenoid makes an operating sound.

REPAIR OR REPLACE TRANSMISSION WIRE

Shift Solenoid "D" Control Circuit
DESCRIPTION Shifting from 1st to 5th is performed in combination with "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, SL3, S4 and SR which are controlled by ...

Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)
SYSTEM DESCRIPTION The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle spee ...

Other materials:

Replacement
1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM SST 07110-58060 (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080) (a) Turn the A/C switch to ON. (b) Operating the cooler compressor at the engine rpm of approx. 1,000 for 5 to 6 minutes, circulate the refriger ...

Short to B+ in Front Passenger Side Squib 2nd Step Circuit
DTC B1188/56 Short to B+ in Front Passenger Side Squib 2nd Step Circuit DESCRIPTION The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front passenger airbag assembly. The circuit instructs the SRS to deploy when deployment conditions are m ...

Engine Control System Malfunction
DTC C1201/51 Engine Control System Malfunction DESCRIPTION If trouble occurs the engine control system, the ECM transmits the abnormality to the skid control ECU. The skid control ECU set this DTC and the skid control ECU prohibits TRAC and VSC control. INSPECTION PROCEDURE 1 CHECK ENGIN ...

В© 2011-2024 Copyright www.tsienna.net