Toyota RAV4 manuals

Toyota Sienna Service Manual: Short in Driver Side Squib 2nd Step Circuit

DTC B1180/17 Short in Driver Side Squib 2nd Step Circuit

DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1180/17 is recorded when a short circuit is detected in the driver side squib 2nd step circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1180/17

  • Short circuit between D2+ wire harness and D2- wire harness of driver side squib 2nd step
  •  Driver side squib 2nd step malfunction
  •  Spiral cable malfunction
  •  Center airbag sensor assembly malfunction
  • Steering pad (Driver side squib 2nd step)
  •  Spiral cable
  •  Center airbag sensor assembly
  •  Instrument panel wire

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the steering pad.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable.

CAUTION: Never connect a tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B1180/17 is not output. HINT: Codes other than DTC B1180/17 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE STEERING PAD

2 CHECK CONNECTORS

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the spiral cable.
  4.  Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK: The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

REPLACE SPIRAL CABLE

3 CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

  1. Disconnect the connector from the center airbag sensor assembly.
  2.  Release the activation prevention mechanism built into connector "B" (7).
  3.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 5

4 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the steering pad and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B1180/17 is not output.

HINT: Codes other than DTC B1180/17 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

5 CHECK INSTRUMENT PANEL WIRE

CHECK INSTRUMENT PANEL WIRE

  1. Disconnect the instrument panel wire connector from the spiral cable.

    HINT: The activation prevention mechanism of connector "B" has already been released.

  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

6 CHECK SPIRAL CABLE

CHECK SPIRAL CABLE

  1. Release the activation prevention mechanism built into connector "D" (7).
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

REPLACE SPIRAL CABLE

USE SIMULATION METHOD TO CHECK

Short to B+ in Curtain Shield Squib LH Circuit
DTC B1168/86 Short to B+ in Curtain Shield Squib LH Circuit DESCRIPTION The curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH ...

Open in Driver Side Squib 2nd Step Circuit
DTC B1181/18 Open in Driver Side Squib 2nd Step Circuit DESCRIPTION The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. ...

Other materials:

Engine immobiliser system
PARTS LOCATION SYSTEM DESCRIPTION The engine immobiliser system has been designed to prevent the vehicle from being stolen. This system uses a transponder key ECU that stores the key code of the authorized ignition key. If an attempt is made to start the engine using a non-authorized key, ...

Removal
1. REMOVE REAR DOOR SCUFF PLATE LH 2. REMOVE REAR DOOR WEATHERSTRIP LH 3. REMOVE BACK DOOR WEATHERSTRIP 4. REMOVE BACK DOOR SCUFF PLATE 5. REMOVE QUARTER TRIM FRONT PANEL ASSEMBLY LH 6. REMOVE VOLTAGE INVERTER ASSEMBLY  Disconnect the connector.  Remove the 2 bolts and the v ...

Driving in vehicle-to-vehicle distance control mode
This mode employs a radar sensor to detect the presence of vehicles up to approximately 400 ft. (120 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to maintain a suitable following distance from the vehicle ahead. Note that vehicle-to-vehicle distance will ...

В© 2011-2025 Copyright www.tsienna.net