Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to B+ in CAN Bus Line

DESCRIPTION

A short to B+ is suspected in the CAN bus wire when the resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom

Trouble Area

The resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  • Short to B+ in CAN bus wire
  • ECM
  • Network gateway ECU
  • Skid control ECU with Actuator
  • Steering angle sensor
  • Yaw rate sensor
  • Distance control ECU
  • Junction connector
  • CAN junction connector

WIRING DIAGRAM

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

HINT: Operating the ignition switch, any switches, or any doors triggers related ECU and sensor communication with the CAN. This communication will cause the resistance value to change.

1 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN BUS WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN BUS WIRE)

  1. Turn the ignition switch off.
  2. Disconnect the ECM connector .

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN BUS WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE ECM

2 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY MAIN BUS WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY MAIN BUS WIRE)

  1. Disconnect the Network gateway ECU connector .

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY MAIN BUS WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE NETWORK GATEWAY ECU

3 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)

  1. Disconnect the junction connector (J17).
  2. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

4 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - NETWORK GATEWAY MAIN BUS WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - NETWORK GATEWAY MAIN BUS WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Result

Result

5 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - ECM MAIN BUS WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - ECM MAIN BUS WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE WIRING HARNESS CONNECTOR (JUNCTION CONNECTOR)

6 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - CAN JUNCTION CONNECTOR MAIN BUS WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (JUNCTION CONNECTOR - CAN JUNCTION CONNECTOR MAIN BUS WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

7 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

8 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Result

Result

REPLACE WIRING HARNESS CONNECTOR (JUNCTION CONNECTOR)

9 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DISTANCE CONTROL ECU BRANCH WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DISTANCE CONTROL ECU BRANCH WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE WIRING HARNESS CONNECTOR (JUNCTION CONNECTOR)

10 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - JUNCTION CONNECTOR MAIN BUS WIRE)

  1. Disconnect the junction connector (J49).

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - JUNCTION CONNECTOR MAIN BUS WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

11 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - ECM MAIN BUS WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR - ECM MAIN BUS WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

12 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)

Standard resistance

Standard resistance

REPLACE WIRING HARNESS CONNECTOR (CAN JUNCTION CONNECTOR)

13 CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

  1. Disconnect the skid control ECU connector.

CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE ABS & TRACTION ACTUATOR ASSEMBLY

14 CHECK CHECK FOR TO B+ IN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

CHECK CHECK FOR TO B+ IN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

  1. Disconnect the steering angle sensor connector

CHECK CHECK FOR TO B+ IN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE STEERING ANGLE SENSOR

15 CHECK CHECK FOR TO B+ IN BUS WIRE (DISTANCE CONTROL ECU BRANCH WIRE)

 CHECK CHECK FOR TO B+ IN BUS WIRE (DISTANCE CONTROL ECU BRANCH WIRE)

  1. Disconnect the distance control ECU connector.

 CHECK CHECK FOR TO B+ IN BUS WIRE (DISTANCE CONTROL ECU BRANCH WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

16 CHECK CHECK FOR TO B+ IN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)

CHECK CHECK FOR TO B+ IN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)

  1. Disconnect the yaw rate sensor connector

CHECK CHECK FOR TO B+ IN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE YAW RATE SENSOR

Short in CAN Bus Lines
DESCRIPTION The CAN bus wires are considered to be shorted when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω. Symptom Trouble Area ...

Short to GND in CAN Bus Line
DESCRIPTION A short to GND is suspected in the CAN bus wire when the resistance between terminals 4 (CG) and 6 (CANH), or terminals 4 (CG) and 14 (CANL) of the DLC3 is below 200 Ω. ...

Other materials:

Front Occupant Classification Sensor LH Collision Detection
DTC B1785 Front Occupant Classification Sensor LH Collision Detection DESCRIPTION DTC B1785 is output when the occupant classification ECU receives a collision detection signal sent by the front occupant classification sensor LH if an accident occurs. DTC B1785 is also output when the front ...

Favorites list setting
Up to 15 contacts (maximum of 4 numbers per contact) can be registered in the favorites list. Registering the contacts in the favorites list Select “Add Favorite”. Select the desired contact to add to the favorites list. Dimmed contacts are already stored as a favorite. Check that a ...

Transmission Range Sensor Circuit Malfunction (PRNDL Input)
DESCRIPTION The park/neutral position switch detects the shift lever position and sends signals to the ECM. HINT: After confirming DTC P0705, use the intelligent tester to confirm the PNP switch signal in the ALL menu (to reach the ALL menu: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ...

© 2011-2024 Copyright www.tsienna.net