Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to B+ in Driver Side Squib Circuit

DTC B0103/12 Short to B+ in Driver Side Squib Circuit

DESCRIPTION

The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0103/12 is recorded when a short to B+ is detected in the driver side squib circuit.

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK STEERING PAD (DRIVER SIDE SQUIB)

CHECK STEERING PAD

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the steering pad.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable.

CAUTION: Never connect a tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory.
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs.

OK: DTC B0103/12 is not output.

HINT: Codes other than DTC B0103/12 may be output at this time, but they are not related to this check.

REPLACE STEERING PAD

2 CHECK DRIVER SIDE SQUIB CIRCUIT

CHECK DRIVER SIDE SQUIB CIRCUIT

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the spiral cable.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  6.  Turn the ignition switch to the ON position.
  7.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Connect the connectors to the steering pad and the center airbag sensor assembly.
  4.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Clear the DTCs stored in memory.
  7.  Turn the ignition switch to the LOCK position.
  8.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  9.  Check the DTCs.

OK: DTC B0103/12 is not output.

HINT: Codes other than code B0103/12 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

4 CHECK INSTRUMENT PANEL WIRE

 CHECK INSTRUMENT PANEL WIRE

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the instrument panel wire connector from the spiral cable.
  4.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5.  Turn the ignition switch to the ON position.
  6.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

5 CHECK SPIRAL CABLE

CHECK SPIRAL CABLE

  1. Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

USE SIMULATION METHOD TO CHECK

Short to GND in Driver Side Squib Circuit
DTC B0102/11 Short to GND in Driver Side Squib Circuit DESCRIPTION The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. The circu ...

Short in Front Passenger Side Squib Circuit
DTC B0105/53 Short in Front Passenger Side Squib Circuit DESCRIPTION The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly. ...

Other materials:

Data list / active test
1. READ DATA LIST HINT: Using the intelligent tester's DATA LIST allows switch, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.  Connect the intelligent tester with CAN VIM to the DLC3. &n ...

Open in Occupant Classification ECU Battery Positive Line
DTC B1794 Open in Occupant Classification ECU Battery Positive Line DESCRIPTION This circuit consists of the occupant classification ECU and the power source circuit (battery, fuse, wire harness). DTC B1794 is recorded when a malfunction is detected in the occupant classification ECU or t ...

Right Front Wheel Speed Sensor Signal
DESCRIPTION The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the ABS control system. The front and rear rotors have 48 serrations each. When the rotors rotate, the magnetic field emitted by the permanent magnet in t ...

В© 2011-2024 Copyright www.tsienna.net