Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to B+ in Side Squib LH Circuit

DTC B0118/46 Short to B+ in Side Squib LH Circuit

DESCRIPTION

The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH (side squib LH).

This circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0118/46 is recorded when a short to B+ is detected in the side squib LH circuit

DTC No.

DTC Detecting Condition

Trouble Area

B0118/46

  • Short circuit in side squib LH wire harness (to B+)
  • Side squib LH malfunction
  • Center airbag sensor assembly malfunction
  • Front seat side airbag assembly LH (Side squib LH)
  • Center airbag sensor assembly
  • Floor wire

INSPECTION PROCEDURE

HINT:

1 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front seat side airbag assembly LH.
  4.  Connect the black wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the front seat side airbag assembly LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs

OK: DTC B0118/46 is not output.

HINT: Codes other than DTC B0118/46 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT SEAT ASSEMBLY LH

2 CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  6.  Turn the ignition switch to the ON position.
  7.  Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE FLOOR WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. ) Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.
  4.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Clear the DTCs stored in memory (5).
  7.  Turn the ignition switch to the LOCK position.
  8.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  9.  Check the DTCs (5).

OK: DTC B0118/46 is not output. HINT: Codes other than code B0118/46 may be output at this time, but they are not related to this check

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short to GND in Side Squib LH Circuit
DTC B0117/45 Short to GND in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH. This circuit ...

Seat Belt Buckle Switch LH Circuit Malfunction
DTC B0126/27 Seat Belt Buckle Switch LH Circuit Malfunction DESCRIPTION The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and the front seat inner belt assembly ...

Other materials:

How to proceed with troubleshooting
1 VEHICLE BROUGHT TO WORKSHOP 2 INSPECT BATTERY VOLTAGE Standard voltage: 11 to 14 V If the voltage is below 11 V, recharge or replace the battery before proceeding. 3 BASIC INSPECTION Turn the ignition switch ON.  Check whether or not the radio receiver turns on. Result 4 CHE ...

Cold Start Ignition Timing Performance
DESCRIPTION This monitor will run when the engine is started at -10 to 50°C (14 to 122°F) of the engine coolant temperature. The DTC will set after the engine idling for 13 seconds (2 trip detection logic). The DTC is designed to monitor the idle air control at cold start. When the ...

Mass air flow meter
COMPONENTS ON-VEHICLE INSPECTION 1. INSPECT MASS AIR FLOW METER NOTICE: Perform the mass air flow (MAF) meter inspection by following the procedures below. Only replace the MAF meter when the MAF value in the DATA LIST (with the engine stopped) are not within th ...

© 2011-2024 Copyright www.tsienna.net