Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to GND in Curtain Shield Squib LH Circuit

DTC B1167/85 Short to GND in Curtain Shield Squib LH Circuit

DESCRIPTION

The curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1167/85 is recorded when a short to ground is detected in the curtain shield squib LH circuit.

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the curtain shield airbag assembly LH.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire.

    CAUTION: Never connect a tester to the curtain shield airbag assembly LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

    Insert the SST straight into the terminals of the connector.

    SST 09843-18060

  5.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Clear the DTCs stored in memory.
  8.  Turn the ignition switch to the LOCK position.
  9.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  10.  Check the DTCs

OK: DTC B1167/85 is not output.

HINT: Codes other than DTC B1167/85 may be output at this time, but they are not related to this check.

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH

2 CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB LH CIRCUIT)

CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB LH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the curtain shield airbag assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory.
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs.

OK: DTC B1167/85 is not output.

HINT: Codes other than code B1167/85 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

Open in Curtain Shield Squib LH Circuit
DTC B1166/88 Open in Curtain Shield Squib LH Circuit DESCRIPTION The curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH. Th ...

Short to B+ in Curtain Shield Squib LH Circuit
DTC B1168/86 Short to B+ in Curtain Shield Squib LH Circuit DESCRIPTION The curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH ...

Other materials:

Open in Driver Side Squib 2nd Step Circuit
DTC B1181/18 Open in Driver Side Squib 2nd Step Circuit DESCRIPTION The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. The circuit instructs the SRS to deploy when deployment conditions are met. DTC B1181/18 is reco ...

Sound Signal Circuit between Radio and Navigation Assembly and Stereo Jack Adapter
DESCRIPTION The stereo jack adapter sends an external device sound signal to the radio and navigation assembly through this circuit. The sound signal that has been sent is amplified by the stereo component amplifier and then is sent to the speakers. If there is an open or short in the c ...

Warning lights and indicators
The warning lights and indicators on the instrument cluster and center panel inform the driver of the status of the vehicle’s various systems. For the purpose of explanation, the following illustration displays all warning lights and indicators illuminated. Vehicles with monochrome displ ...

© 2011-2024 Copyright www.tsienna.net