Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to GND in Curtain Shield Squib RH Circuit

DTC B1162/81 Short to GND in Curtain Shield Squib RH Circuit

DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1162/81 is recorded when a short to ground is detected in the curtain shield squib RH circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1162/81

  • Short circuit in curtain shield squib RH wire harness (to ground)
  • Curtain shield squib RH malfunction
  • Center airbag sensor assembly malfunction
  • Curtain shield airbag assembly RH (Curtain shield squib RH)
  • Center airbag sensor assembly
  • Floor wire No. 2

INSPECTION PROCEDURE

HINT:

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the curtain shield airbag assembly RH.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire No. 2.

CAUTION: Never connect a tester to the curtain shield airbag assembly RH (Curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B1162/81 is not output. HINT: Codes other than DTC B1162/81 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH

2 CHECK FLOOR WIRE NO.2 (CURTAIN SHIELD SQUIB RH CIRCUIT)

 CHECK FLOOR WIRE NO.2 (CURTAIN SHIELD SQUIB RH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire No. 2.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE NO.2

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the curtain shield airbag assembly RH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4. Clear the DTCs stored in memory (5).
  5. Turn the ignition switch to the LOCK position.
  6. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B1162/81 is not output. HINT: Codes other than DTC B1162/81 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Open in Curtain Shield Squib RH Circuit
DTC B1161/84 Open in Curtain Shield Squib RH Circuit DESCRIPTION The curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH. Th ...

Short to B+ in Curtain Shield Squib RH Circuit
DTC B1163/82 Short to B+ in Curtain Shield Squib RH Circuit DESCRIPTION The curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH ...

Other materials:

Evaporator temperature sensor
ON-VEHICLE INSPECTION 1. INSPECT A/C EVAPORATOR TEMPERATURE SENSOR (a) Remove the A/C evaporator temperature sensor (A/ C thermistor). (b) Disconnect the connector from the A/C evaporator temperature sensor (A/C thermistor). (c) Measure the resistance according to the value(s) in the ...

Removal
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait for 90 seconds after disconnecting the cable to prevent the airbag working. 2. REMOVE FRONT SEAT ASSEMBLY HINT:  Refer to the instructions for removal of the front seat assembly (for flat type).  Refer to the in ...

Installation
1. INSTALL REAR AXLE HUB & BEARING ASSEMBLY LH (a) Install the hub & Bearing assembly LH with the 4 bolts. Torque: 56 N*m (571 kgf*cm, 41 ft.*lbf) 2. INSPECT BEARING BACKLASH (See page AH-16) 3. INSPECT AXLE HUB DEVIATION (See page AH-16) 4. CONNECT SKID CONTROL SENSOR WIRE (a) Co ...

В© 2011-2024 Copyright www.tsienna.net