Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to GND in Driver Side Squib 2nd Step Circuit

DTC B1182/19 Short to GND in Driver Side Squib 2nd Step Circuit

DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1182/19 is recorded when a short to ground is detected in the driver side squib 2nd step circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1182/19

  • Short circuit in driver side squib 2nd step wire harness (to ground)
  • Driver side squib 2nd step malfunction
  • Spiral cable malfunction
  • Center airbag sensor assembly malfunction
  • Steering pad (Driver side squib 2nd step)
  • Spiral cable
  • Center airbag sensor assembly
  • Instrument panel wire

INSPECTION PROCEDURE

HINT:

1 CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the steering pad.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the spiral cable.

CAUTION: Never connect a tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B1182/19 is not output. HINT: Codes other than DTC B1182/19 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE STEERING PAD

2 CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the spiral cable.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

Go to step 4

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the steering pad and the center airbag sensor assembly.
  2. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B1182/19 is not output. HINT: Codes other than DTC B1182/19 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

4 CHECK INSTRUMENT PANEL WIRE

CHECK INSTRUMENT PANEL WIRE

  1. Disconnect the instrument panel wire connector from the spiral cable.
  2.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

5 CHECK SPIRAL CABLE

CHECK SPIRAL CABLE

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE SPIRAL CABLE

USE SIMULATION METHOD TO CHECK

Open in Driver Side Squib 2nd Step Circuit
DTC B1181/18 Open in Driver Side Squib 2nd Step Circuit DESCRIPTION The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. ...

Short to B+ in Driver Side Squib 2nd Step Circuit
DTC B1183/22 Short to B+ in Driver Side Squib 2nd Step Circuit DESCRIPTION The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering ...

Other materials:

Perform zero point calibration of yaw rate and deceleration sensor (when using sst check wire)
NOTICE: While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it in a stationary condition. (Do not turn the ignition switch to the ON position.) Be sure to do this on a level surface (with an inclination of less than 1 %). (a) Proc ...

Fuel sender gauge assembly
INSPECTION 1. INSPECT FUEL SENDER GAUGE ASSEMBLY  Disconnect the connector from the fuel sender gauge.  Check that the float moves smoothly between F and E.  Measure the resistance between terminals 1 and 2 of the connector according to the value(s) in the table b ...

Terminals of ECU
1. TELEVISION CAMERA ASSEMBLY  Disconnect the T10 camera connector Measure the voltage and resistance of each terminal of the wire harness side connector. If the result is not as specified, there may be a malfunction on the wire harness side.  Reconnect the T10 ...

В© 2011-2025 Copyright www.tsienna.net