Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to GND in Front Passenger Side Squib 2nd Step Circuit

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Short to GND in Front Passenger Side Squib 2nd Step Circuit

DTC B1187/55 Short to GND in Front Passenger Side Squib 2nd Step Circuit

DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1187/55 is recorded when a short to ground is detected in the front passenger side squib 2nd step circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1187/55

  • Short circuit in front passenger side squib 2nd step wire harness (to ground)
  •  Front passenger side squib 2nd step malfunction
  •  Center airbag sensor assembly malfunction
  • Front passenger airbag assembly (Front passenger side squib 2nd step)
  • Center airbag sensor assembly
  • Instrument panel wire

INSPECTION PROCEDURE

HINT:

1 CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)

CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front passenger airbag assembly.
  4.  Connect the black wire side of SST (resistance 2.1 Ω) to the instrument panel wire.

CAUTION: Never connect a tester to the front passenger airbag assembly (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B1187/55 is not output. HINT: Codes other than DTC B1187/55 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2 CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT)

CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the instrument panel wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B1187/55 is not output. HINT: Codes other than DTC B1187/55 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Open in Front Passenger Side Squib 2nd Step Circuit
DTC B1186/58 Open in Front Passenger Side Squib 2nd Step Circuit DESCRIPTION The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front passenger ...

Short to B+ in Front Passenger Side Squib 2nd Step Circuit
DTC B1188/56 Short to B+ in Front Passenger Side Squib 2nd Step Circuit DESCRIPTION The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front pa ...

Other materials:

Reassembly
1. BEARING POSITION 2. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE (a) Install the differential gear lube apply tube and transaxle apply tube clamp with the bolt to the transaxle housing. Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf) NOTICE: Make sure to insert the pipe to the s ...

Installation
1. INSTALL BRAKE MASTER CYLINDER (a) Install the brake master cylinder with the 2 nuts. Torque: 13 N*m (130 kgf*cm, 9 ft.*lbf) (b) Slide the clip and connect the brake master cylinder reservoir hose. (c) Using SST, connect the 2 brake tube to the brake master cylinder. SST 09023-001 ...

Before driving
Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eyelets. Turn the upper knob of each retaining hook (clip) to secu ...

В© 2011-2025 Copyright www.tsienna.net