Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to GND in Side Squib LH Circuit

DTC B0117/45 Short to GND in Side Squib LH Circuit

DESCRIPTION

The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0117/45 is recorded when a short to ground is detected in the side squib LH circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B0117/45

  • Short circuit in side squib LH wire harness (to ground)
  • Side squib LH malfunction
  • Center airbag sensor assembly malfunction
  • Front seat side airbag assembly LH (Side squib LH)
  • Center airbag sensor assembly
  • Floor wire

INSPECTION PROCEDURE

HINT:

1 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front seat side airbag assembly LH.
  4. Connect the black wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the front seat side airbag assembly LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs

OK: DTC B0117/45 is not output.

HINT: Codes other than DTC B0117/45 may be output at this time, but they are not related to this check

Go to step 2

REPLACE FRONT SEAT ASSEMBLY LH

2 CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

 CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B0117/45 is not output.

HINT: Codes other than code B0117/45 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Open in Side Squib LH Circuit
DTC B0116/48 Open in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side assembly LH. This circuit instructs the S ...

Short to B+ in Side Squib LH Circuit
DTC B0118/46 Short to B+ in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH (side squib LH). ...

Other materials:

Removal
1. Drain automatic transaxle fluid (a) Remove the drain plug, gasket and drain ATF. (b) Install a new gasket and the drain plug. Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 2. Drain transfer oil (for 4wd) Hint: (see page tf-8) 3. Remove front wheel 4. REMOVE FRONT AXLE HUB LH NUT (a) Us ...

Automatic transaxle fluid
On-vehicle inspection 1. CHECK FLUID LEVEL HINT: Drive the vehicle so that the engine and transaxle are at normal operating temperature. Fluid temperature: 70 to 80°C (158 to 176°F) (a) Park the vehicle on a level surface and set the parking brake. (b) With the engine idling and the ...

How to proceed with troubleshooting
HINT: Troubleshoot in accordance with the procedures on the following pages. 1 VEHICLE BROUGHT TO WORKSHOP 2 CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK 3 INSPECT COMMUNICATION FUNCTION OF LARGE-SCALE MULTIPLEX COMMUNICATION SYSTEM (BEAN) Use the intelligent tester to check for norma ...

© 2011-2024 Copyright www.tsienna.net