1. SPEED SENSOR SIGNAL CHECK (WHEN USING SST CHECK WIRE):
HINT:
(a) Turn the ignition switch off.
(b) Check that the steering wheel is in the straightahead position and move the shift lever to the P position (Automatic Transmission) or apply the parking brake (Manual Transmission).
(c) Using SST, connect terminals TS and CG of the DLC3.
SST 09843-18040
(d) Turn the ignition switch to the ON position.
(e) Check that the ABS warning light is blinking in the Test Mode.
HINT: If the ABS warning light does not blink, inspect the TS and CG terminal circuit and the ABS warning light circuit.
(f) Start the engine.
(g) Using SST, perform the speed sensor signal check in Test Mode.
SST 09843-18040
(h) Drive the vehicle straight forward.
(i) Accelerate the vehicle to a speed of 28 mph (45 km/ h) or higher for several seconds and check that the ABS warning light goes off.
HINT: The signal check may not be completed if the vehicle has its wheels spun.
(j) Stop the vehicle.
NOTICE:
Decelerate or stop the vehicle before the speed reaches 50 mph (80 km/h).
HINT: When the signal check has been completed, the ABS warning light goes off while driving and blinks in the Test Mode pattern while stationary.
2. READ DTC
(a) Using SST, connect terminals TC and CG of the DLC3.
SST 09843-18040
(b) Read the number of blinks of the ABS warning light.
HINT:
(c) After performing the check, disconnect the SST from terminals TS and CG, TC and CG of the DLC3 and turn the ignition switch off.
3. DTC OF TEST MODE (SIGNAL CHECK) FUNCTION
HINT: The codes in this table are output only in Test Mode (signal check).
4. SPEED SENSOR SIGNAL CHECK (WHEN USING INTELLIGENT TESTER):
HINT:
(a) Turn the ignition switch off.
(b) Check that the steering wheel is in the straightahead position.
(c) Connect the intelligent tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Set the intelligent tester to Test Mode (select "SIGNAL CHECK").
HINT: Refer to the intelligent tester operator's manual for further details.
(f) Check that the ABS warning light is blinking in the Test Mode.
HINT: If the ABS warning light does not blink, inspect the TS and CG terminal circuit and the ABS warning light circuit.
(g) Start the engine.
(h) Using the intelligent tester, perform the speed sensor signal check in Test Mode.
(i) Drive the vehicle straight forward.
(j) Accelerate the vehicle to a speed of 28 mph (45 km/ h) or higher for several seconds and check that the ABS warning light goes off.
HINT: The signal check may not be completed if the vehicle has its wheels spun.
(k) Stop the vehicle.
NOTICE:
Decelerate or stop the vehicle before the speed reaches 50 mph (80 km/h).
HINT: When the signal check has been completed, the ABS warning light goes off while driving and blinks in the Test Mode pattern while stationary.
5. READ DTC
(a) Read the DTC(s) by following the tester screen.
HINT:
6. DTC OF TEST MODE (SIGNAL CHECK) FUNCTION
HINT: The codes in this table are output only in Test Mode (signal check).
How to proceed with
troubleshooting
HINT:
Troubleshoot in accordance with the procedures on the
following pages.
1 VEHICLE BROUGHT TO WORKSHOP
2 CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK
3 PROBLEM SYMPTOMS TABLE
When problem is not listed on problem symptoms table,
proceed to A.
When problem is listed on pro ...
Indicator Circuit
DESCRIPTION
The indicator displays the location of the obstacle and the approximate
distance between the vehicle and
the obstacle either by blinking or turning on.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - AIR CONDITIONER
AMPLIFIER)
...
Short in Front Pretensioner Squib RH Circuit
DTC B0130/63 Short in Front Pretensioner Squib RH Circuit
DESCRIPTION
The front pretensioner squib RH circuit consists of the center airbag sensor
assembly and the front seat
outer belt assembly RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
DTC B0130/63 ...