Toyota RAV4 manuals

Toyota Sienna Service Manual: Trouble in Passenger Airbag ON / OFF Indicator

DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag, the front seat side airbag RH and front seat belt pretensioner RH condition (activated/not activated) by the passenger airbag ON/OFF indicator.

HINT: Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger airbag ON/ OFF indicator will be ON/OFF depending on the conditions listed below.

DESCRIPTION

INSPECTION PROCEDURE

1 CHECK SRS WARNING LIGHT

  1. Turn the ignition switch to the ON position, and check the SRS warning light condition.

HINT: If this trouble occurs, the SRS warning light is off. If it is on, a DTC is output. Troubleshoot for the output DTC.

OK: After the primary check period, SRS warning light goes off. HINT: The primary check period is approximately 6 seconds after the ignition switch is turned to the ON position

2 PERFORM ZERO POINT CALIBRATION

  1. Turn the ignition switch to the LOCK position.
  2. Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETE" is displayed

3 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

END

4 RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT

  1. Turn the ignition switch to the LOCK position.
  2.  Loosen the 4 installation bolts of the front seat assembly RH.
  3.  Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf)

5 PERFORM ZERO POINT CALIBRATION

  1. Connect the intelligent tester to the DLC3.
  2.  Turn the ignition switch to the ON position.
  3.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETE" is displayed.

6 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

END

7 CHECK CONNECTORS

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Check the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

    OK: The connectors are connected.

  4.  Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.
  5.  Check the connectors are not damaged or deformed.

    OK: The connectors are properly normal.

8 CHECK DTC

  1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.
  2. Connect the negative (-) terminal cable to the battery.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4. Turn the ignition switch to the LOCK position.
  5.  Clear the DTCs stored in the memory.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (35).

OK: DTC is not output.

9 REPLACE OCCUPANT CLASSIFICATION ECU

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Replace the occupant classification ECU

10 PERFORM ZERO POINT CALIBRATION

  1. Connect the negative (-) terminal cable to the battery.
  2.  Connect the intelligent tester to the DLC3.
  3.  Turn the ignition switch to the ON position.
  4.  Using the intelligent tester, perform "Zero point calibration" (28).

OK: "COMPLETE" is displayed.

11 PERFORM SENSITIVITY CHECK

  1. Using the intelligent tester, perform "Sensitivity check" (28).

Standard value: 27 to 33 kg (59.52 to 72.75 lb)

END

Sleep Operation Failure of Occupant Classification ECU
DTC B1796 Sleep Operation Failure of Occupant Classification ECU DESCRIPTION During sleep mode, the occupant classification ECU reads the condition of each sensor while the ignition switch is of ...

Steering pad
Components ...

Other materials:

CD Abnormal/ Excess Current/ Tray Insertion / Ejection Error/ CD Abnormal/ Excess Current/ Tray Insertion / Ejection Error
DTC 62-44 CD Abnormal DTC 62-48 Excess Current DTC 62-50 Tray Insertion / Ejection Error DTC 63-44 CD Abnormal DTC 63-48 Excess Current DTC 63-50 Tray Insertion / Ejection Error DESCRIPTION DTC No. DTC Detecting Condition Trouble Area 62-44 Operation error ...

Freeze frame data
1. DESCRIPTION  The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whe ...

Inspection
1. INSPECT BRAKE DRUM INSIDE DIAMETER (a) Using a brake drum gauge or equivalent, measure the inside diameter of the drum. Standard inside diameter: 254.0 mm (10.00 in.) Maximum inside diameter: 256.0 mm (10.08 in.) 2. INSPECT REAR DRUM BRAKE SHOE LINING THICKNESS (a) Using a ruler, ...

В© 2011-2025 Copyright www.tsienna.net