Toyota RAV4 manuals

Toyota Sienna Service Manual: Removal

Toyota Sienna Service Manual / Engine hood / door / Power slide door / Removal

HINT: On the RH side, use the same procedures as on the LH side.

1. REMOVE SLIDE DOOR

REMOVE SLIDE DOOR

  1. Remove the rear door scuff plate (See page IR-7).
  2. Remove the back door scuff plate (See page ED- 214).
  3. Remove the quarter trim panel (See page IR-9).
  4. Remove the upper rail cushion from the rail.
  5. Disconnect the 2 connectors from the body side and remove the bolt and wire.

REMOVE SLIDE DOOR

  1. Open the quarter glass.
  2. Using a screwdriver, disengage the clip and 2 claws, remove the rail end moulding.

HINT: Tape the screwdriver tip before use.

REMOVE SLIDE DOOR

  1. Remove the 2 bolts and bracket center No. 2 together with the tensioner (color: white).
  2. Remove the tensioner from the bracket center No.

    2.

REMOVE SLIDE DOOR

  1. Remove the 2 bolts and bracket center No. 1 together with the tensioner (color: black).
  2. Remove the tensioner from the bracket center No.

    1.

REMOVE SLIDE DOOR

  1. Remove the 2 nuts and open stop.

REMOVE SLIDE DOOR

  1. Rotate the base of the slide door roller lower in the direction indicated by arrow in the illustration and then remove the roller from the cut area of the lower rail from the body side.

REMOVE SLIDE DOOR

  1. Move the slide door rearward and then remove the slide door roller upper from the cut area in the rear part of the slide door rail upper.

REMOVE SLIDE DOOR

  1. Move the slide door further rearward and then remove the slide door hinge center from the rear part of the slide door rail center. Then, remove the slide door.

2. REMOVE SLIDE DOOR RAILS

  1. Remove the roof headlining (See page IR-6).
  2. Remove the 2 bolts, 2 nuts and the rail upper.
  3. Remove the 2 screws and rear side rail.
  4. Remove the 3 screws and rail center

3. REMOVE SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY LH

REMOVE SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY LH

  1. Disconnect the 2 cables.
  2. Remove the 2 bolts and full open stop lock.

4. REMOVE SLIDE DOOR ROLLER ASSEMBLY LOWER LH

REMOVE SLIDE DOOR ROLLER ASSEMBLY LOWER LH

  1. Remove the 3 bolts and roller.

5. REMOVE SLIDE DOOR HINGE ASSEMBLY CENTER LH

REMOVE SLIDE DOOR HINGE ASSEMBLY CENTER LH

  1. Remove the 3 bolts and hinge.
  2. LH side: Remove the cover.

6. REMOVE SLIDE DOOR ROLLER ASSEMBLY UPPER

  1. Remove the 2 bolts and roller.
Power slide door
COMPONENTS ...

Disassembly
1. REMOVE REAR DOOR WINDOW FRAME MOULDING REAR LH (See page ET-31) 2. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH (See page ET-32) 3. REMOVE SLIDE DOOR WINDOW GARNISH LH Fully o ...

Other materials:

Suspension system
How to proceed with troubleshooting HINT: This is the repair procedure for vehicle pull. Problem symptoms table FRONT SUSPENSION SYSTEM REAR SUSPENSION SYSTEM ...

Radio Broadcast cannot be Received or Poor Reception
INSPECTION PROCEDURE 1 CHECK RADIO AND NAVIGATION ASSEMBLY Check the radio's automatic station search function. Check the radio's automatic station search function by activating it. OK: The radio's automatic station search function works properly. 2 INSPECT RADIO AND NAVIGATION AS ...

If the vehicle becomes stuck
Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow: Stop the engine. Set the parking brake and shift the shift lever to P. Remove the mud, snow, or sand from around the stuck tire. Place wood, stones or some other material under the tires ...

В© 2011-2024 Copyright www.tsienna.net